Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 1 Average
  • 1
  • 2
  • 3
  • 4
  • 5

60B Version 2 Grille Cloth
#1

Oh, no!  Not grille cloth again!  I’ve searched the forums but haven’t found a specific reference to version 2.

I finished the cabinet restoration a few days ago, but had second thoughts about the grille cloth.  When I acquired the set it had faded, worn & torn cloth which I assumed was original.  So I replaced it with closely-matching  Radio Daze GRC-03.  Since then I’ve noticed that none of the photos I’ve seen of a 60B Version 2 have this pattern--not even in a 1934 Philco ad picture.
 
[Image: https://farm5.staticflickr.com/4640/3820...b9687d.jpg]
[Image: https://farm5.staticflickr.com/4589/2505...39f6ba.jpg]

The set has had some previous work done, but it’s pretty old.  One filter cap is replaced with a cardboard electrolytic from the Illinois Condenser Co, so how old might that be?

Do I have the wrong grille cloth?  If so, is an appropriate replacement available?

Thanks from a woefully disappointed…
Henry
#2

Definitely the wrong cloth. Philco had not started using the chevron cloth yet when the 60B Version 2 was being produced.

This version of the 60 also used what is commonly known among collectors as the "70/90 cloth pattern".

An exact duplicate is no longer available, but you can get pretty close with Kenny Richmond's Whiskey Rayon, or Radio Daze's GRC02.

P.S. I hate to tell you this, but in that "after" photo, the cabinet was not toned properly.

--
Ron Ramirez
Ferdinand IN
#3

Thanks, Ron. I KNEW you would notice the tone. I couldn't tell the difference on the set before restoration--it all looked equally dark. I picked up the error after it was finished. But I had a good time doing it, anyway.




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM

[-]
Who's Online
There are currently 1404 online users. [Complete List]
» 1 Member(s) | 1403 Guest(s)
Avatar

>