Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Was the escutcheon on Model 19B Polished?
#1

Hello, I have a Philco Model 19B with a cabinet that is in nearly perfect original condition. The escrutcheon is a dull brass. I was wondering if the escrutcheon was originally polished or if it would have been unpolished. It seems that most collectors prefer to not have it polished, but is this original? 

Thanks
#2

Welcome to the Phorum!
Icon_wave
#3

A rule of collecting: never remove patina.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#4

I seem to recall that Doug Houston (RIP) once told me that those escutcheons were never highly polished brass, but were always dark even when new.

--
Ron Ramirez
Ferdinand IN
#5

Thank all of you very much. I like the unpolished look but was always curious how it looked when new.
#6

Those bright golden one you see sometimes...just look wrong.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#7

If that is the case a bit of toned lacquer will darken it up.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#8

If someone has polished an escutcheon to bright shine, you can darken it again, using gun bluing.
#9

Or, as Terry said, with some Extra Dark Walnut toner. Icon_smile

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 4336 online users. [Complete List]
» 1 Member(s) | 4335 Guest(s)
Avatar

>