Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 66b Alignment Instructions
#1

Can anyone supply me with Rider's "Aligning Philco Receivers" for the model 66b? Icon_confused

Bob
#2

The basic alignment info is in Riders at:
http://www.nostalgiaair.org/PagesByModel...013827.pdf

Its rather short and sweet.

There is a document "Aligning Philco Receivers" out there that I'm sure you can find as a download on the web. Its worthwhile to read if you are new to alignment. In the meanwhile, if you have any specific questions feel free to ask here. The 66 is a basic set with no special techniques necessary.
#3

Thanks for the tip. I am new to alignment. I do have the Model 66 schematic and instructions, page 5-31, from Nostalgaiair. I also have the "Aligning Philco Receivers" document prepaired by the Philco Service Department for Radio Manufacturers Service. It covers the Model 60b but doesn't cover the Model 66b. I saw Ron's old post on the Rider's Model 60 in 2007 and am wondering if the same type info is available on the Model 66? It seemed to have a little more info with several pictorials. I'm not ready to start the alignment yet but want to get as much info as possibel before getting started.

Bob
#4

Don't " overthink" alignment and don't be intimidated. Other than component numbers its the same drill on all these sets. A five-minute job if you have done it once before Icon_smile

I/we will be glad to help if you have questions.




Users browsing this thread:
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 3102 online users. [Complete List]
» 1 Member(s) | 3101 Guest(s)
Avatar

>