Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-216 restoration questions
#61

I try not to touch these at all, and when I find the insulation is cracked, if it is not crumbling badly, I just put heatshrinkable tubing over.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#62

Does anyone sell new bushings for the tuner?

They look similar to renovatedradios "t01" part for Hippo radio but may not be as long. It's the closest I can find so may just have to try.

[Image: https://i.imgur.com/UnvN1y1.jpg]

[Image: https://i.imgur.com/RZcku7p.jpg]

t01
http://www.renovatedradios.com/product.php?product=313
#63

Measure the old one carefully, and compare to Ed's (Renovated Radios) measurements for T01. You can always cut off excess rubber, but you can't easily add more on...

--
Ron Ramirez
Ferdinand IN
#64

There's one he sells for tuning caps for 37-116 and likes. Could just fit.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#65

On my 116's I've used 2 rubber grommets from the hardware store per bolt/sleeve. One is 7/16" od and fits the hole in the chassis. the other is 5/16" od w/a 3/16 hole for the sleeve to fit thru. Cut the small grommet in half putting one half on top and the other on the bottom of the larger grommet.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#66

Does this wire even show on the schematic?

Gimmick?

[Image: https://i.imgur.com/xlXxZ0N.jpg]
#67

Yup it's a gimmick cap to add a bit of osc signal into the mixer.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#68

Just for fun here is the stepping unit in action today.

I have the remote but am just now starting to work on it.

This video shows it in action triggered by my sig gen.

https://www.youtube.com/watch?v=SL5f5hAWVsQ
#69

So what is the best red jewel to get these days for the On light?
#70

So restoration is complete but I am seeing one strange thing going on.

I can fire the unit up and have it set to a known freq. When the audio comes up it seems fine but then about 2 minutes later I get a POP and then it all comes up louder.

I know I have at least one weak tube.

What would make the POP and everything come up louder at the same time?

Once it's warmed up it's fine.

THoughts?
#71

More than likely one of the tubes has a slight internal short that clears as the tube gets hot.

Gregb
#72

I'll have to work on getting some replacement tubes at some point. Icon_smile




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Delco car radio Peko vibrator converstion issues
Rich, There is an Australian website (Cool386.com) that has much useful info regarding repair and restoration of vibr...Joe Rossi — 07:29 PM
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM

[-]
Who's Online
There are currently 3551 online users. [Complete List]
» 4 Member(s) | 3547 Guest(s)
AvatarAvatarAvatarAvatar

>