1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Internal loop connection 40-190
soldersucker
Junior Member
**
Posts: 7
Threads: 2
Joined: Feb 2018
City: Lancaster,Ohio
#1

02-15-2018, 08:31 PM
Took out the loop in the top of the cabinet during cabinet restore. Put it back in ,got one side to the tuning cap,where does the other side hook up? Schematic says ground but wire will not reach . Loop is stock afaik.
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

02-15-2018, 09:20 PM
Hi SS and welcome,
The small loop is for the SW band and connects from chassis ground (short wire at the tuning condenser) and lug 3 on the back terminal strip long wire.

GL
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 02-15-2018, 09:22 PM by Radioroslyn.)
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#3

02-16-2018, 12:28 AM
Welcome to the Phorum!
Icon_wave
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
soldersucker
Junior Member
**
Posts: 7
Threads: 2
Joined: Feb 2018
City: Lancaster,Ohio
#4

02-16-2018, 06:33 PM
Lug 3 was blank ,sw ant. wire fit ok there.! Kinda funky sw ant. Thanks for the help. Sure I will be back with more questions. Icon_biggrin
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently 4572 online users. [Complete List]
» 1 Member(s) | 4571 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration