1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 87 question
Micro9
Junior Member
**
Posts: 36
Threads: 15
Joined: Aug 2007
City: Glendale,AZ
#1

05-13-2010, 12:01 AM
Philco 87 chassis has been rebuilt...new caps resistors tubes...I algined it according to the procedure on Philco Radio.com and neturalize the set as well....Radio plays with plenty of voulmm from about 700 up to 1600 but low volumm on stations 700 and below.....any ideas???Thanks... Icon_idea
Find
exray
Phorum Expert
*****
Posts: 893
Threads: 9
Joined: Mar 2008
City: Vieques, PR USA State, Province, Country: PR
#2

05-13-2010, 07:15 AM
Something I'd look for would be a short between plates in one (or more) of the tuning gangs as the tuning cap is meshed closed.
Website Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#3

05-14-2010, 03:25 PM
Something else to try is tune to a station down at the low end. Then try touching the stators one by one on the tuning cap. If volume increases you've got a tracking issue with the rf amps.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
Micro9
Junior Member
**
Posts: 36
Threads: 15
Joined: Aug 2007
City: Glendale,AZ
#4

05-15-2010, 08:41 PM
Thanks for the input...Looks like I have an open RG coil to the 1st RF tube...
took it aprt and it is broken in 4 diffent places....Does anyone have a spare RF coil for a Philco 87?? Philco part number is
3075-A
Find
Micro9
Junior Member
**
Posts: 36
Threads: 15
Joined: Aug 2007
City: Glendale,AZ
#5

05-17-2010, 12:52 AM
UPDATE...
Got brave and soldered the wire back together and rewound the coil...Put it
back together and realign and Neuturalized it and now the lower station come in loud and clear...
Thanks for everone's help on this...
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#6

05-17-2010, 10:23 AM
That is good news. Congratulations! Icon_biggrin
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5041 online users. [Complete List]
» 2 Member(s) | 5039 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration