Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 71 code 225? Should I restore or sell as is??
#1

Hi there,
I'm not a radio buff..but I love old stuff!!..I have a Philco chassis model71 code 225...it needs a little work/refinishing. It worked the last time I plugged it in...about 2 years ago. I'm wondering if it is worth it to refinish or should I sell it as is? How much could I expect to get both ways? Or how much would it cost to refinish? I would love to refinish and keep it, because I used it alot growing up and I have nice memories....but with tough times...I will.. regretfully, sell itIcon_sad
Any advise would be appreciated!!
Thanks
#2

My thought would be, if you grew up with it and have fond memories, keep it! When I grew up, we had an RCA console radio. I don't know what ever happened to it but I wish I had it now. I'm not sure what model it was. So hang on to your radio if you can.
Steve

M R Radios   C M Tubes
#3

Smart money says that if you aren't familiar with old radios then it would probably be a bad idea to do anything to it in hopes of increasing its value. I've seen too many examples of things that have been redone by professional 'furniture' restorers that ruined the item from a 'radio' collector perspective. (Coloring, finish type, etc). A radio is not an old chair Icon_smile

That said, if you were to find a real radio restorer the cost would rarely be recouped upon resale.

If you're intent on selling it I'd recommend doing so as-is. Original examples often are more desirable than a refurbed example - particularly so if the refurb is short on authentic details.

Guessing dollar values is out of the question without seeing photos. (Is my girlfriend pretty?) Icon_wink
#4

If general, you won't make much money on a quick flip, especially if it is a one time deal and you are new to refinishing.
To make money on radios, you need to be excellent at refinishing woodwork and sell to the yuppies on eBay who get stupid over deep glossy piano grade finishes.
Fellow collectors are notoriously cheap. I'd sell as-is or keep. You won't get rich selling it.

Out of room, still dragging 'em home




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently 5090 online users. [Complete List]
» 1 Member(s) | 5089 Guest(s)
Avatar

>