Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Started the restore on my Philco 40-180.
#16

Ok thanks Ron, I have already ordered some zebrawood veneer off eBay. I just never heard eBay, called e-pay before.

Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.
#17

I don't care for their business model so the disrespect is intentional. But, some sellers are worth doing business with. Usually once I make a purchase, I keep the sellers site/address so I can deal directly with them.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#18

I've never had a problem with eBay, but have with PayPal. About 8 yrs ago, they sent me a bill for $270., but refused to send me an invoice so I could see what the bill was for. They finally sent it to collections. after 8 years, I have never payed it, and they still refuse to send me an invoice.
Michael

Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.
#19

I’m not sure I have it down on how to post pictures but hopefully I got it right. 
I tried to post a before and after photo of my Philco 40-180 cabinet. I had to totally replace the veneer strips on either side of the speaker. I think the replacement veneer is a pretty close match to the original!
#20

Alright, I received the zebra-wood veneer a couple days ago, managed to get it cut.installed it yesterday, turned out pretty good.

[attachment=16665]

I spent the week with grain filler, and sanding sealer, then the zebra-wood veneer, today I sprayed 2 coats of Mohawk ultra flo clear Lacquer. Tomorrow a little light sanding, then 2 more coats of lacquer. Then see where I stand. heres a picture of one side, got too dark to do the other side.

[attachment=16666]

Michael

Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.
#21

I never got and answer about the plastic piece that was on the inside of the top of the cabinet, all that was there was the 4 corners 2 on each side. Looks like it was 4in wide and went across from one side to the other. It was brown, does anybody know what that was?
Michael

Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.
#22

Methinks it's missing the ant loop for the high SW band.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#23

(06-30-2018, 11:01 AM)Radioroslyn Wrote:  Methinks it's missing the ant loop for the high SW band.

That makes sense, I have never seen one listed anywhere. Have any ideas where I might find one?

Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.
#24

Sorry I haven't been back on here, been busy looking for a new house, put both radios on the back burner till after we move. We close on the new house on the 24th, so after the move, I will have a 36X48 shop to work in. Will get back to them then just a little work to do on the 41-295, and still need to work in the chassis for the 40-180. Both cabinets are done.
Michael

Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>