Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

BATTERY ACID REPAIR
#1

Hello everyone.  Recently I became the owner of a beautiful Freed - Eisemann nr-10 in a full cabinet with battery storage area.  Photos are in the July Finds and Losses section of the Phorum.  The side panel of the cabinet was exposed to battery acid and has a fist-sized area of discoloration and wood rot as a result from the interior out through the external finish.  Any ideas as to how I can repair this?  The panel only seems to be 1/4 inch plywood.  My initial idea was to remove the damaged area, refill the area with a new section of wood or filler, then re-veneer the exterior and refinish the entire cabinet.  I'm hoping you guru's have a better idea.  Thanks in advance, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#2

Depends on your abilities. If the rest of the cabinet is really good, a repair to just the damaged panel would be best. It can be done, but matching grains and colors is not covered in Cabinet Repair 101. (Advanced skills required)

Pitchers?

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#3

We would need to see the damage to make an evaluation, for a start the acid would have to be neutralized in some way before any repair to that panel could be made, no need if it is to be replaced. I can remember neutralizing the battery shelf in the bottom of an old battery console from the late 1930s with a baking soda solution years ago, lots of fizzing action.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>