Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-116 Mag Tuning question
#1

I've had one for close to 30yrs now that I got at an auction for $35. When I got it I replaced all the caps and such and it work great. About 10yrs ago it died and I'm thinking about putting her up on the bench and seeing what the matter is. I have a simple question. Does the mag tuning operate on the BC band only or will it act as an afc circuit on SW?
Tnx
Terry
Going the pickup a 37-675 tomorrow!! Tnx to Pete in NJ

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#2

Hi Terry,

I restored a 37-675 (non tele-dial version) a few years ago. I believe that the 675 and 116 use the same sub-chassis. I thought that the magnetic tuning was used on all bands on the 675 and the schematic for the 116 confirms that. I was very pleased with the performance of the 675. If I had not bought a 16X I would have kept the 675. That sub chassis was a major pain to work on.

Sean
WØKPX
#3

7estatdef Wrote:I've had one for close to 30yrs now that I got at an auction for $35. When I got it I replaced all the caps and such and it work great. About 10yrs ago it died and I'm thinking about putting her up on the bench and seeing what the matter is. I have a simple question. Does the mag tuning operate on the BC band only or will it act as an afc circuit on SW?
Tnx
Terry
Going the pickup a 37-675 tomorrow!! Tnx to Pete in NJ

Works on all bands. See the Magnetic Tuning info from my site:

PHILCO SERVICE HINTS & TIPS - NUMBER 33
Aligning the Magnetic Tuning System
http://www.philcorepairbench.com/tips/svctip33.htm

Chuck




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5693 online users. [Complete List]
» 1 Member(s) | 5692 Guest(s)
Avatar

>