Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

HELP Need a Philco expert
#1

Hi all. I have a 71 cathedral that is beautiful but quite silent.  I can't seem to get it to oscillate at all. I have rewound the primary (small outer coil) on the oscillator coil but it still won't play.  This radio actually belongs to a customer of mine.  I have completely recapped it and checked all the resistors and tubes.  If someone can take a look he will pay you what ever it takes. Thanks.

If it glows in the dark and heats up the house its MY kind of radio!  Icon_crazy
#2

So are you looking for troubleshooting help to fix it yourself or someone to fix it?

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

I really want to send the chassis and speaker to someone who can take a close look at it and find the problem.

If it glows in the dark and heats up the house its MY kind of radio!  Icon_crazy
#4

Has the chassis been recapped and checked otherwise the way it's supposed to before power-up?

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#5

Yes. I checked it out. The amp works fine, just won't oscillate.

If it glows in the dark and heats up the house its MY kind of radio!  Icon_crazy
#6

(09-24-2018, 12:44 PM)sumnerplace Wrote:  I really want to send the chassis and speaker to someone who can take a close look at it and find the problem.

If you do not feel comfortable working on it yourself, then you should do the following:

1. Place an ad in the "Wanted Ads" section of the Phorum.
Go to the Phorum home page - scroll down - keep scrolling until you are close to the bottom of the page - you will see For Sale or Trade and Wanted Ads.

2. Use the Resources pages here in the Phroum to find a radio repairman near you.
Look under Philco Info > Philco Resources.

I see you are in Washington state. There are two radio clubs in your part of the country - Puget Sound Antique Radio Association and the newer Inland Empire Antique Radio Society. Contact one (or both) of these clubs and see if they can recommend someone close to you that can work on your radio for you.
http://www.pugetsoundantiqueradio.com/
http://www.iears.org/

--
Ron Ramirez
Ferdinand IN
#7

Thanks Ron. I'll do that

If it glows in the dark and heats up the house its MY kind of radio!  Icon_crazy
#8

Ron I can't find the Philco Info page or the Resources page. Can you help me?

If it glows in the dark and heats up the house its MY kind of radio!  Icon_crazy
#9

http://philcoradio.com/phorum/showthread.php?tid=14951
#10

http://philcoradio.com/phorum/showthread.php?tid=14950

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Radio city products 664 schematic request
Need a schematic or manual for the 664. The 663 may be similar.daveone23 — 12:38 PM
New Philco Repair Bench
Thanks Gary.dconant — 12:16 PM
New Philco Repair Bench
I tried accessing the site through our library and got the same response. It's reported to our tech gurus. GaryGarySP — 11:50 AM
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM

[-]
Who's Online
There are currently 7599 online users. [Complete List]
» 2 Member(s) | 7597 Guest(s)
AvatarAvatar

>