Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

GE model GD-60
#1

Yesterday after a disappointing trip to the Hartville Flea Martket (don't get me started on it), I stopped in at an antiques shop nearby and bought an unusual little General Electric radio. I initially mistook it for an old intercom as it looks alot like one! Turned out it is a model GD-60 am "compact" radio with five tubes and one ballast tube. Radio is complete and in decent shape, but there was one moment of panic. I pulled the chassis to inspect it and was presented with a crumpled, butchered, crumbling, and flaking asbestos pad! ARG! I grabbed a dust mask and some disposable gloves and hauled the cabinet outside for an asbestos removal. I managed to get it removed, sealed in a plastic bag and disposed of safely. If it had been intact I would have left it alone, but this thing was falling apart! Plenty of vents in the bottom of the cabinet to keep things cool though. I will have thise little guy rebuilt soon. It is kinda unique looking. Icon_biggrin

No matter where you go, there you are.
#2

cool I have many radios with asbestos lining the wood under the chassis popular problem. By the way just bought a zenith 8G625 at a flea market. Old radios are so cool!
#3

I found one of those in an antique store several years ago. It had sat in water at some time. I refinished the cabinet, replaced decals on both knobs, and worked on the chassis. Just played it a few days ago...sounds good. One of my "keepers."
#4

Mine just went out with a group of radios to be rebuilt yesterday, so hopefully I'll hear it speak soon.

No matter where you go, there you are.
#5

Nice looking set!!! If your ballast tube is open it can be replaced with a diode on this set.
Good luck!
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently 2905 online users. [Complete List]
» 3 Member(s) | 2902 Guest(s)
AvatarAvatarAvatar

>