Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA 110K2 Unexpected project
#91

The first coat of oil dried up, leaving dull patches where it had coated bare wood. On Wednesday morning I found time to pass gently over the right side of the cabinet with 0000 wire wool, and rub in another coat of tung oil. Looking again this morning, it appears this approach is working nicely, a deep color and good finish is beginning to develop.

I have refinished a number of pieces of furniture this way, including our "Danish Modern" coffee table. This had been very neglected before we got to it, but (a lot of) TLC returned it to glory.

I don't hold with furniture that talks.
#92

OK, here are a couple of hasty garage shots of the cabinet after a little more refinishing attention today. Coming along nicely, I think:

   

   

I don't hold with furniture that talks.
#93

Nice Job! I have a 110k console sitting waiting for the chassic to come back to me. A friend is going through it. I do not have the know how of replacing the caps and such. My radio cabinet looks nothing like brand new but its good enough. Hope they both work great when done.  Icon_thumbup
#94

More picture later. I declared satisfaction with the cabinet, and refitted the chassis, grillecloth, speaker etc.

Done!

I don't hold with furniture that talks.
#95

And here she is:

I went downstairs this morning to take a picture, and discovered two things. One, the preset buttons were acting lazy, calling for a little lubrication. Second, a casual glance revealed the dial glass was in backwards! All corrected now, and it plays nicely:


   

I don't hold with furniture that talks.
#96

Looks great Ed  Icon_thumbup

Did you mention that you used Tung oil to touch up the finish?

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#97

Thanks Elliot

Yes, Tung oil. It seems to work best applied quite sparingly in several sessions. Allow a few days in between rub-downs. I don't know if it works with grain filling products, but I have applied it over fillers (furniture repair and refinishing) with good results.

Cheers,

Ed

I don't hold with furniture that talks.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>