1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
53-706 winter project
SteveinAlaska
Junior Member
**
Posts: 19
Threads: 7
Joined: Feb 2016
City: Fairbanks Alaska
#1

11-12-2018, 11:41 PM
Expecting 4 to 8 inches of snow with 30 mph winds so it looks like winter finally is here Icon_lol!
So I am starting with this little gem for the 1st winter project.
Missing the lamp, the cabinet is a little worse for the wear, but all the rest of electronics are there (chassis & clock).
Found a schematic to work with.

Questions ......... is there a specific style/type lamp assembly that I should use?
Telechron clock.......I see the Philco part# 41-2043, is there a Telechron model number somewhere?

There is a blown resistor (47000) to begin with & someone else has worked on it before. So, I start from square one on this.

I welcome any thoughts, comments & suggestions
Springtime comes about end of April around here.
Find
David
Phorum Expert
*****
Posts: 1,191
Threads: 25
Joined: Jan 2014
City: Wellborn Florida
#2

11-13-2018, 08:23 AM
   
Good morning Steve. Posting a link to a GE radio that has some good info on the clock, Please do not use WD 40 on the clock use a good light weight oil.  http://www.nostalgiaair.org/pagesbymodel...007697.pdf
Find
SteveinAlaska
Junior Member
**
Posts: 19
Threads: 7
Joined: Feb 2016
City: Fairbanks Alaska
#3

11-13-2018, 03:29 PM
....and I thank you for the help & info!
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#4

11-13-2018, 06:47 PM
Not sure which lamp you are referring to? The pilot lamp is going to be a #47 and the 120v lamp I would use something 40w or less incandescent. LED's might generate noise.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
SteveinAlaska
Junior Member
**
Posts: 19
Threads: 7
Joined: Feb 2016
City: Fairbanks Alaska
#5

11-14-2018, 02:47 AM
Sorry 'bout that - it's the 120 volt lamp I was wondering about.
Did Philco make (or use) a particular type or brand of lamp base??
Find
David
Phorum Expert
*****
Posts: 1,191
Threads: 25
Joined: Jan 2014
City: Wellborn Florida
#6

11-14-2018, 08:30 AM
OK so I am half blind. The only light I see is the number 47 bulb hooked to pins 4 an 6 of the 35W4
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#7

11-14-2018, 11:44 AM
This particular model has a dial lamp, a clock, and is a desk lamp/ am radio.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration