Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Eaton Viking 40A75E1 - a large Viking from Canadian forests
#16

Arran, thank you very much for the very interesting information. Icon_thumbup  Icon_thumbup  Icon_thumbup

I have 6F5, but I do not use it basically because of its too high level of distortion and the "pentode" character of the sound. So used a more delightful 6Q7 lamp.

Gregb, thanks for the suggestion. Icon_thumbup  I will think how that can be done.
#17

Excellent restoration work, a real fine job.
Icon_clap
Paul

Tubetalk1
#18

Тhank you very much , Paul . Icon_biggrin
#19

Two small video demos ... I am surprised at the almost complete absence of industrial noise, interference from WIFI and household appliances, which is why it's simply impossible to take on many of my other radio ... I think this is achieved thanks to the shielded chassis and frame antenna ...

[Video: https://www.youtube.com/watch?v=4lTJPPqw...aCSbIdo-OW]
#20

[Video: https://www.youtube.com/watch?v=SBNS9T-7...W&index=18]
#21

Great request for forum administrators, - transfer the last 4 posts about the receiver of DB-39 in the topic of my collection.

http://philcoradio.com/phorum/showthread.php?tid=12318

Thanks .
#22

Your wish is my command, sir.

Done.

http://philcoradio.com/phorum/showthread...#pid150668

Icon_smile

--
Ron Ramirez
Ferdinand IN
#23

Thank you, Ron. Icon_thumbup




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM
Zenith H725
When dealing with noise on power lines, time to get my Jackery 240 out. Talk about clean can hold a portable am radio ne...David — 08:52 PM
Zenith H725
Arran - I bet you're right probably vinyl, there was no rubber smell when desoldering it, which you often get with the o...EdHolland — 08:23 PM
Zenith H725
Ed; It was very likely vinyl covered wire given the vintage of the set, there was some rubber/gutta percha wire used ...Arran — 06:34 PM

[-]
Who's Online
There are currently no members online.

>