Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Silvertone 9005 just finished this one
#1

New caps, a few resistors and tubes got this back into use. Enjoy the video!
https://www.youtube.com/watch?v=sqmmsLBdXG8
#2

Nice job, I like those sets, I think Arvin made those. 

Paul

Tubetalk1
#3

Hey, I like your bench!  It looks as cluttered as mine! It's the way it should be.
#4

(01-24-2019, 08:42 PM)Paul Philco322 Wrote:  Nice job, I like those sets, I think Arvin made those. 

Paul
Didn't know that it performs well for a AA5.

(01-24-2019, 10:23 PM)rfeenstra Wrote:  Hey, I like your bench!  It looks as cluttered as mine! It's the way it should be.
I believe someone once said the sign of a messy bench means they are a genius.
#5

I always knew that! It's obvious.

   
#6

(01-24-2019, 11:00 PM)rfeenstra Wrote:  I always knew that! It's obvious.
Wooden stool? you need a nice comfy office chair for bench work and were is the fridge for cold drinks?
#7

Good thought!
#8

me gots comfy chairs from an old VFW,, and a usual busy work bench.


Attached Files Image(s)
   
#9

(01-25-2019, 10:00 PM)jcassity Wrote:  me gots comfy chairs from an old VFW,, and a usual busy work bench.

Show off Icon_lol .




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM
Zenith H725
When dealing with noise on power lines, time to get my Jackery 240 out. Talk about clean can hold a portable am radio ne...David — 08:52 PM
Zenith H725
Arran - I bet you're right probably vinyl, there was no rubber smell when desoldering it, which you often get with the o...EdHolland — 08:23 PM
Zenith H725
Ed; It was very likely vinyl covered wire given the vintage of the set, there was some rubber/gutta percha wire used ...Arran — 06:34 PM
Zenith H725
I think the problem is traced - to noise on the AC line. It sounded so local, that it seemed certain it was generated wi...EdHolland — 05:51 PM
The list of my radio & TV collection!
A little bit of positivity in our feed... My new video... Test - the Philco 16B vs Philco 37-116 de Luxe / Test - the ...RadioSvit — 12:14 PM
Refinishing Ideas
Thanks. I will look into. Billpoulsbobill — 11:23 AM

[-]
Who's Online
There are currently 626 online users. [Complete List]
» 2 Member(s) | 624 Guest(s)
AvatarAvatar

>