Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Model 732
#1

Hello all,
I am new to the forum and I'm not even sure if I should be here...
I am in New Zealand where the Philco model numbers are not the same as the USA ones.
Nevertheless, I'm hoping that someone may be able to point me in the direction of a schematic for a Philco Model 732 (S/No: 14053)
Valve Lineup: 7B7, 7A8, 7B7, 7B6, 5Y3, 6V6
Broadcast plus 4 SW bands covering 49M to 16M
Perhaps there is a USA model which has the same lineup and I might glean some clues from that.
Any suggestions welcome.
Many thanks!
#2

Hi and Welcome!
Sure you can be here! It maybe a big help to post a picture of your set. Or you could take a look in the Gallery to find it.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Hello Terry,
Thank you for your encouraging words!
I will take some more shots tomorrow of the "innards", but here it is as I received it.
Also, I may be a wee bit slow, but how do I access the Gallery?
Cheers1
Noel

Note from site admin: Sorry, but the photo which was attached to this post is no longer available.
#4

Based on some information found it was made in 1947 by Philco New Zealand. Sets for Philco New Zealand appeared to be manufactured by Dominion Radio & Electrical Company (DRECO). Other than this information I'm not able to find much unfortunately... I'd say based on cabinet design alone it looks most like a model 46-132 but it's not the same since the US model is AM and it appears only one SW band.

http://www.radiomuseum.org/r/philco_732.html

http://www.radio-restoration.com/Philco.html

http://www.trademe.co.nz/Music-instrumen...299571.htm (good picture for restoration reference)

Brian Mattson
Coon Rapids, MN
#5

Here you go! http://www.philcoradio.com/gallery/
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>