1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
46-1226 factory finish ?? satin of gloss
jstaf40
Junior Member
**
Posts: 43
Threads: 21
Joined: Nov 2010
City: hesperia,ca.92345
#1

11-14-2010, 07:33 PM
i have a 46-1226 code 122 it has a satin finish do you know what was stock finish thanks....john
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#2

11-14-2010, 07:49 PM
Hi

The original finish would have been gloss lacquer.
--
Ron Ramirez
Ferdinand IN
Find
jstaf40
Junior Member
**
Posts: 43
Threads: 21
Joined: Nov 2010
City: hesperia,ca.92345
#3

11-14-2010, 08:12 PM
thank you.... can the finish be put on by brush or spraying only this is my first redo i was 10 yr old when it was made it an old friend
john
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#4

11-14-2010, 08:32 PM
Best results will be achieved by spraying. Lacquer dries very fast, so brushing would be rather difficult, I would think.
--
Ron Ramirez
Ferdinand IN
Find
jstaf40
Junior Member
**
Posts: 43
Threads: 21
Joined: Nov 2010
City: hesperia,ca.92345
#5

11-15-2010, 02:05 PM
thank you for your help.. the forum is a great help to the seniors many who lestened to philco when they were new....captian midnight- the shadow and others that played with your mind not like today mindless tv
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently 5149 online users. [Complete List]
» 1 Member(s) | 5148 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration