Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Grundig 3068 Hi-Fi Zauberklang
#1

I found this today for cheap.  Everything works, except the EM34 tuning eye tube.  It's been playing in a guy's garage for years. He purchased it in Germany in the 1950's. 

I'm always amazed when I see these radios....they are huge.  It sounds great, and the tuner is very sensitive. The cabinet is very clean, as is the dial. There just a small bit of laminate separation at the bottom of one side, that I will be gluing down. 

My first old German radio.

A bunch of odd looking jacks in the back. Can any of these be used to plug in an MP3 player or Bluetooth receiver?  what sort of plugs would it take?

Is there a manual in ENGLISH for these?

Thanks

Grundig 3068 Hi-Fi Zauberklang
[Image: https://i.imgur.com/x9r3Mxa.jpg?1]
#2

Deutchse Intstiut Normung forgive my spelling, usually these have a DIN type jack, my Grundig does, try something like this...............

https://www.amazon.com/TNP-Converter-Equ...4675&psc=1

More info..............

https://en.wikipedia.org/wiki/DIN_connector

My pal Ross who is a Euro Radio Whiz explained to me once that the reason German Engineers get so much performance from minimal tube counts is that radios in Germany were taxed on the amount of tubes they had, so if you keep tube count down you could sell for less. 

My Grundig plays well but the laminate is cracking and pulling off, another one sounds better than looks. 

Good luck. 

Paul

Tubetalk1
#3

I don't see a 5 pin DIN socket. Here is whats back there:

[Image: https://i.imgur.com/4dJCwXj.jpg?1]

[Image: https://i.imgur.com/0CBbZNy.jpg]
#4

How bout this/

https://www.ebay.com/itm/Emud-Grundig-Ra...2816358401

Maybe you can translate the other connector text. 

If no more answers here you can pm me and I can see if I can put you in touch with someone who would know. 

Paul

Tubetalk1
#5

Thanks. I do believe that's what I need.
#6

Hmm - I don't think those are all DIN connectinons. The plug has an outer shell - and I don't see a circular groove around the sockets labeled "HiFi Strahler" and "Fern Dirigent"

Using these terms, I found this thread on the UK vintage site:

https://vintage-radio.net/forum/showthread.php?t=104996

It seems the HiFi socket is an output, and the other was for a remote control system.

The "Tonbandergerat" connection is a DIN type for a tape recorder, and is the most likely possibility to connect a music source. Aufname and Weidergabe translate as recording and playback, suggesting that the radio could be used as a source, and high quality means of listening to recordings.

I don't hold with furniture that talks.
#7

The tuner on this radio is quite good. It is picking up stations quite clearly that my other radios struggle with.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM
Zenith H725
When dealing with noise on power lines, time to get my Jackery 240 out. Talk about clean can hold a portable am radio ne...David — 08:52 PM
Zenith H725
Arran - I bet you're right probably vinyl, there was no rubber smell when desoldering it, which you often get with the o...EdHolland — 08:23 PM
Zenith H725
Ed; It was very likely vinyl covered wire given the vintage of the set, there was some rubber/gutta percha wire used ...Arran — 06:34 PM

[-]
Who's Online
There are currently no members online.

>