1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco Model 90 Tuning Dial
Jonathan Philco 41
New Member
*
Posts: 2
Threads: 1
Joined: Apr 2019
City: Huntsville State, Province, Country: Alabama
#1

04-05-2019, 10:37 AM
Hello friends. I just restored a Philco model 90. Turned out great. As with many of these, the tuning knob/dial slips when tuning. It turns but the dial does not. does anybody have any suggestions on how to fix this tuning bushing or where to obtain a new one?  Thank you.

Jon
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,297
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

04-05-2019, 11:09 PM
Hi Jon and welcome,
Would have replied sooner  but it's been along time since I've serviced a model 90. So what's the problem? Is the tuning shaft pinching the inside of the dial hub correctly?? Is the tuning shaft worn badly so pinching mechanism can't grip the hub. Spring weak?
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
Jonathan Philco 41
New Member
*
Posts: 2
Threads: 1
Joined: Apr 2019
City: Huntsville State, Province, Country: Alabama
#3

04-09-2019, 06:41 PM
Hi Terry . Sorry for the late reply. The radio is put back together. I can tune the radio if I push down on the tuning knob as I turn the tuning knob. I have two model 90's with the same problem. One is worse than the other however. It is irritating indeed. The restore turned out excellent however. Could you send me a private message so I can send you my contact information?
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Refinishing Ideas
Hi Poulsbobl, I think that you could get away with it.  In the Philco Library, there is a parts listand specs for sp...MrFixr55 — 11:54 PM
Philco 46-480 Electronic Restoration
The sleeving for the transformer arrived early, so I went ahead and finished reassembling. The chassis looks far better ...jrblasde — 10:15 PM
Philco 610B oscillator wiring
I don't know what you are referring to when you say "tube cathode ground". Ground is a connection to the chass...RodB — 05:56 PM
Zenith H725
Good points, Arran. I haven't encountered this problem with any other radio (all earlier vintages), so am learning here....EdHolland — 05:32 PM
Zenith H725
Ed; One thing that I will say about these is that Brand Z was considerate enough to make these mica caps easily acces...Arran — 02:34 PM
Philco 610B oscillator wiring
Do you know what run # your chassis is? It took me a while to find what you were basing updates/modification on as I did...Radioroslyn — 07:34 AM
Need to purchase some accessories for restoration of my Old Philco Radio
COLLEAGUES, Thank you all for such good and important suggestions as how to find good replacement parts. I will go fo...palonso — 07:05 AM
Zenith H725
Here's what the inside of AM IFT2 looked like, and the other pic shows the discs I made to take place of the mica and ke...EdHolland — 07:40 PM
Zenith H725
IF2 will need replacement caps. The arcing was severe enough that the mica is pitted and holed where the HT flashed over...EdHolland — 04:04 PM
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios