Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

What do I have here?
#1

I purchased this at an estate sale with no accompanying information. The tube chassis has stamped “D 14170”. Is that the model #?

Mark W
#2

Welcome to the Phorum!

That's not a model number - more likely a serial number.

Info here on identifying Philco radios:
https://philcoradio.com/library/index.ph...ion-guide/

Alternatively post a few pictures and we can help.
#3

Welcome to the Phorum!
Icon_wave
#4

Hi could you tell me what replacement capacitor would I use for BR3045A 3 cap mfds volts 450 thank you James
#5

Hi James and welcome.
To answer your question I'll ask you a question, what Philco model are you servicing??
Part numbers are sometimes hard to sort out when you don't not know what they go to.

Not sure if the post goes w/the 1st three maybe Bob can move it and change it to a separate thread.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#6

Any ideas on what model this is?


Attached Files Image(s)
               
#7

Looks like a 42-365K to me. The three tuning bands seem to match as does the cabinet.
#8

Thank you, Bob!
#9

We do not have a good photo of that model in our gallery. If you could take a few shots of it face on, it would make a nice addition. You can post it here or send it to Nathan Slingerland. Thanks much!!!
#10

More pics
#11

   
#12

Thanks!!




Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 4413 online users. [Complete List]
» 2 Member(s) | 4411 Guest(s)
AvatarAvatar

>