1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco part numbers and values?
NV3G
Member
***
Posts: 74
Threads: 42
Joined: May 2008
City: Shinnston, West Virginia State, Province, Country: USA
#1
Exclamation 

05-13-2019, 10:12 AM
Is there a place I can go on the
Phorum to find the values of a Philco
33-5240-1 dual potentiometer?

Thanks,
Oscar
nv3g
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
#2

05-13-2019, 10:39 AM
And what set is it in??
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
Nathan Slingerland
Super Moderator
******
Posts: 1,872
Threads: 212
Joined: May 2015
City: Seattle State, Province, Country: WA
#3

05-13-2019, 11:57 AM
Depending on the era of the set you might check the relevant parts catalog in the Philco Library:

https://philcoradio.com/library/index.php/parts/

There's also a searchable parts reference in the Philco Library - but it is currently limited to 1939 and earlier parts info and doesn't contain the part you listed.
https://philcoradio.com/library/index.ph...-controls/
Find
NV3G
Member
***
Posts: 74
Threads: 42
Joined: May 2008
City: Shinnston, West Virginia State, Province, Country: USA
#4

05-13-2019, 04:09 PM
Philco 38-690
Find
Nathan Slingerland
Super Moderator
******
Posts: 1,872
Threads: 212
Joined: May 2015
City: Seattle State, Province, Country: WA
#5

05-13-2019, 04:19 PM
Old Phorum thread to the rescue!

https://philcoradio.com/phorum/showthread.php?tid=13625
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM

[-]
Who's Online
There are currently 3588 online users. [Complete List]
» 3 Member(s) | 3585 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration