1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Film caps in place of electrolytics.
jake wells
Still Learning.
***
Posts: 194
Threads: 43
Joined: Jan 2019
City: Brownsville 42210 State, Province, Country: Kentucky
#1

05-30-2019, 02:54 AM
Been reading on some restore threads where the electrolytic can is being restuffed with a solen fast cap? Are they electrolytic or plain film?
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

05-30-2019, 03:31 AM
They are film caps.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
jake wells
Still Learning.
***
Posts: 194
Threads: 43
Joined: Jan 2019
City: Brownsville 42210 State, Province, Country: Kentucky
#3

05-30-2019, 05:09 AM
So what is the deal of using them over traditional electrolytics?
Find
morzh
Odobenus rosmarus
*****
Posts: 15,825
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#4

05-30-2019, 08:47 AM
The electrolytic capacitor is officially a limited lifetime part.
The film capacitor is unlimited lifetime part. Also self-healing. Also has much better ripple/ESR characteristics.
So where it fits (they are large: the electrolytic claim to fame is large capacitance density) it is a good idea to put it in instead.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 05-30-2019, 08:47 AM by morzh.)
Find
EdHolland
Phorum Expert
*****
Posts: 1,287
Threads: 44
Joined: Nov 2017
City: Menlo Park State, Province, Country: CA
#5

05-30-2019, 11:30 AM
On my 16X, I had to put something where the Mershon electrolytics would have been. Two film type metal cased motor caps were fixed using a home made strap in a configuration close to the original, with paper insulation around the cans.

I have since obtained a set of original caps which could be restuffed and fitted to the chassis. I may get to this, but am happy with the look, performance and hopefully long life of the film caps
I don't hold with furniture that talks.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration