Need help on 40-180 chassis
Posts: 17
Threads: 3
Joined: May 2019
City: Cincinnati
State, Province, Country: Ohio
OK, just got everything back together and did what morzh said to do. So with the signal generator hooked up to the antenna screw thru a .1 cap and volumn all the way up I put 40 AC volts of signal to the plates. Then I connect the voltmeter to the secondary side of the OT and had at times .7 volts max and it would drop to 0 and fluctuate from 0 to .7 volts. So looks like my problem is the transformer is not putting out. I will be looking for a replacement. Learning experience for me so thanks mortzh. I'll know more how to test these in the future. Once I find another I'll post the results.
Posts: 15,853
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
Bill
Yes the secondary fluctuating if the primary is steady is not good.
However, at 0.7V AC you should've heard a fairly loud signal. Maybe a fluctuating but still.
Have you measured the resistances of the primary halves?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 06-07-2019, 09:24 PM by morzh.)
Posts: 17
Threads: 3
Joined: May 2019
City: Cincinnati
State, Province, Country: Ohio
224 ohms on one side and 197 ohms on the other which is close to what the schematic calls for: 240 & 210. I've yet to get any signal out of the speaker. The weak signal I can hear comes from the output trans and it fluctuates with moving the dial on the signal generator so I know thats the signal I'm feeding in.
Posts: 15,853
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
Are you sure the connection of the xfmr to the speaker is good?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 17
Threads: 3
Joined: May 2019
City: Cincinnati
State, Province, Country: Ohio
Yes I have checked that. Made sure no break in the plug at the end of the wiring harness. So one side of the trans secondary is to chassis ground, other to speaker voice coil. made sure all connections are the same as original trans I took out.
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Hi Bill and welcome to the fray,
If you need an output transformer here is a reasonably priced one. https://www.tubesandmore.com/products/tr...output-8-w
GL w/your project.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 06-08-2019, 10:49 AM by Radioroslyn.)
Posts: 15,853
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
Yes theirs are way more reasonably priced than Hammonds. About 1/3 of the price.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 17
Threads: 3
Joined: May 2019
City: Cincinnati
State, Province, Country: Ohio
Thanks for the link. I may try that one. Haven't had any luck finding an old one in my stash that would work. Price is better than others I've seen. Hopefully that will take care of it.
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
You may want to check the resistance of the spkr's voice coil just to be sure it isn't open. I don't see it very often but it does happen. To do this disconnect the output transformer's secondary from the voice as it will influence the measurement. Should see a very low resistance of a few ohms.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 15,853
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
Terry
He said he took the speaker and tested it with another radio.
This is the only reason I haven't suggested it so far, else I'd do the same.
Also this is why I asked about the connection from the xfmr to the speaker.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 06-08-2019, 02:45 PM by morzh.)
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
>He said he took the speaker and tested it with another radio
My brain must have skipped over that part. That's assuming I can read, sometimes that's questionable! [Image: https://philcoradio.com/phorum/images/sm...on_lol.gif]
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 17
Threads: 3
Joined: May 2019
City: Cincinnati
State, Province, Country: Ohio
Update on my problem with this 40-180 chassis. Went ahead and got the new output trans that Radioroslyn suggested. Did not solve the problem but I could hear sound thru the speaker a little better but very weak. Felt I had checked all that I could so I contacted a member of one of our local clubs that has been doing this for years. Took it to him and he was stumped for maybe 15 minutes. First thought it might be the switch on the push button for tuning but it was OK. Had output from the new trans when measured at the trans but not so much at the voice coil so he tried a jumper from the chassis to the voice coil and BAM, that was it! He said he had come across this once before. THe speaker I was using was not the exact one but from another Philco. His explanation basically was that the field coil was a little different and was not connected to the ground from the wiring harness. So simple fix was I ran a 5th wire from the voice coil to the ground screw on the chassis and all is well. Maybe this will help anyone else with a 40-180 that needs another speaker.
Thanks to all that offered help on this.
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
38-10T chassis Restoration begins
|
| Arran
I also washed tuning caps in dishwasher and in soap water without having removed the micas.
Upon drying, it wa...morzh — 02:00 PM |
|
38-10T chassis Restoration begins
|
| Hi Richard, I used to build houses and we used a lot of those gold flake counter tops. We even used gold flake ceramic t...dconant — 11:11 AM |
|
38-10T chassis Restoration begins
|
| Hello Guys,
Don't mind my 1950s kitchen countertop and funny thing about that countertop it has little what looks like ...radiorich — 10:53 AM |
|
38-10T chassis Restoration begins
|
| Hello Dconant,
Very funny but here is Photo of my Gemoro ultrasonic cleaner !
Arran , I have not had any issues eith...radiorich — 10:48 AM |
|
Philco 60 Squealing
|
| Radio is playing right now and sounding good.dconant — 08:54 AM |
|
38-10T chassis Restoration begins
|
| I don't think it is as critical as some would think. I've washed chassis, typically on hot days during the summer time, ...Arran — 07:51 AM |
|
Rusty Tuning Condenser
|
| I would try something like Evaporust, or a similar product, there is a guy on Y.T that does this with aluminum fined tun...Arran — 05:14 AM |
|
Rusty Tuning Condenser
|
| Be careful with aluminum vane caps.
I did that, with dishwasher; it dulled the whole thing, which became grey.
No, no,...morzh — 10:19 PM |
|
Rusty Tuning Condenser
|
| Hello Rob. I've also heard of soaking the tuning cap in automatic transmission fluid. This was an old trick we used to...GarySP — 06:14 PM |
|
Rusty Tuning Condenser
|
| Gary, I once had a tuning cap that had a thick coat of kitchen grease and grime. So I had heard about brake cleaner bei...RodB — 06:03 PM |
|
Who's Online
|
There are currently 1451 online users. [Complete List]
» 1 Member(s) | 1450 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
