Posts: 66
Threads: 7
Joined: Jun 2019
City: Austin
State, Province, Country: Minnesota
im restoring a Philco 42 PT-7 radio for the first time and I’ve heard i could get shocked if I’m not careful.. What are my real dangers with it unplugged? I also heard on YouTube that paper capacitors should just be automatically replaced because they’ll likely go out soon if they’re not already. Can I just clip the wires on them (provided I take plenty of pics beforehand) without any dangers? My snips do have plastic handles so I should be good as far as that part goes… The guy who I bought it from on eBay said it did light up but no sound came out. Any guesses to what maybe wrong? I’m guessing likely a bad tube? But that’s only a guess, I have not attempted to plug it in myself I downloaded the schematic for it but I’m not sure how to read it. I don’t want any of my faults to keep me from trying to restore this thing though.
Any help would be nice!
Thanks,
Adam
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Hi Adam,
>What are my real dangers with it unplugged?
Very little. Would be a freak sort of accident to get shocked.
>I’m guessing likely a bad tube? [Image: https://philcoradio.com/phorum/images/sm...on_lol.gif][Image: https://philcoradio.com/phorum/images/sm...n_evil.gif]
More than likely there will be several issues to correct. A tube or two may be part of the problem. Unless your set came from CA you are probably going to have decaying rubber wire which can be a bit of a pain to replace
> I downloaded the schematic for it but I’m not sure how to read it.
Not sure what you are saying. Is it just schematics w/vacuum tubes or you have no clue as to how to decipher what you are looking at on any schematic?
http://www.nostalgiaair.org/pagesbymodel...013568.pdf
GL
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 06-21-2019, 08:10 PM by Radioroslyn.)
Posts: 15,818
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
>>>>Can I just clip the wires on them (provided I take plenty of pics beforehand) without any dangers? My snips do have plastic handles so I should be good as far as that part goes
Not sure I got you right: are you implying snipping wires while plugged and powered? If yes, you are having some serious issues with understanding safety and should not attempt at repairs until familiarizing yourself with rules of it.
If not then why the plastic handles matter?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 66
Threads: 7
Joined: Jun 2019
City: Austin
State, Province, Country: Minnesota
Thanks for the info, Terry. The schematic i downloaded and printed off is the exact one you attached. I think I’m starting to understand it better
Posts: 66
Threads: 7
Joined: Jun 2019
City: Austin
State, Province, Country: Minnesota
No, I’m not that crazy.. Of course it’ll be unplugged before I even attempt to replace anything, I’m only 40.. I want to live longer! Lol
Posts: 66
Threads: 7
Joined: Jun 2019
City: Austin
State, Province, Country: Minnesota
I just know that some capacitors can hold a lethal charge even when the item they’re attached to isnt even plugged In, that was main concern and that’s why I mentioned the rubber grips on my tools so I should be good I’m thinking as far as that goes. The table I’m working on isn’t metal either
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
I would presume you are not familiar with electronics ?
do you know how to solder ?
read schematics ?
all round paper caps should be replaced so should electrolytics
take lot of good pics for reference
and ask a lot of questions
sam
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Posts: 1,523
Threads: 240
Joined: Sep 2012
City: West Bend, Wisconsin
While the little pre-war transitones are relatively simple in design, for a first attempt at restoring a radio it may not be the best choice due to the extremely cramped chassis and crumbling wire wrapped around everything. Be aware that any wire that gets disturbed will more than likely have its coating crumbling off, leaving you with a bare wire. Not good. Totally rewiring the radio to replace ALL of the crumbling wire would be preferred (see Ron's thread for a somewhat similar set up: https://philcoradio.com/phorum/showthread.php?tid=19779) but that would probably be above the skill level of someone just starting out. You may opt to just replace or sleeve the ones that are bare with shrink tubing, or at the very least use some liquid tape on a toothpick to coat the bare spots on the wire. Good luck!
Greg V.
West Bend, WI
Member WARCI.org
Posts: 1,402
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO
If your radio is unplugged, it is safe to work on. The tubes are still hot the moment the power is turned off and will continue to conduct for a second or two, this will discharge the capacitors.
Steve
M R Radios C M Tubes
Posts: 15,818
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
.....unless the radio was plugged in without the speaker, in which case the charge persists longer and we are all guilty of doing that every once in a while 
Or the transformer is open.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 06-22-2019, 09:19 PM by morzh.)
Posts: 66
Threads: 7
Joined: Jun 2019
City: Austin
State, Province, Country: Minnesota
Do I change the blue capacitor shown in the pic? And if so, with what? It says 20 + 20 MFD on it..
Thanks
(This post was last modified: 06-23-2019, 04:18 PM by Arohn19.)
Posts: 66
Threads: 7
Joined: Jun 2019
City: Austin
State, Province, Country: Minnesota
For some reason the pic isn’t posting
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Check the size of the pic you may have to resize it (smaller) the Phorum doesn't do it automatically.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 120
Threads: 15
Joined: Aug 2017
City: Fort Worth
State, Province, Country: TX
What radio are you working on? What does the schematic or parts list show for electrolytic capacitors? The 20 + 20 means there are two 20 MFD electrolytic capacitors present. If the part is original or old, it would need to be replaced. Easiest way to do that is with two separate 20 or 22 MFD electrolytic capacitors of an appropriate voltage rating.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Two separate threads started by the OP have been merged into one.
Arohn19, separate threads on the same subject are not allowed per Phorum rules.
https://philcoradio.com/phorum/showthread.php?tid=4586
Please read and familiarize yourself with the Rules. Thanks.
--
Ron Ramirez
Ferdinand IN
Users browsing this thread: 19 Guest(s)
|
|
Recent Posts
|
|
Shadow Meter Bulb
|
| Ok. Thanks for the correction.RossH — 03:09 PM |
|
Model 28L
|
| For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM |
|
37-60 revision 6
|
| I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM |
|
Shadow Meter Bulb
|
| Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM |
|
Hickok AC51 tube tester
|
| Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM |
|
Model 28L
|
| Hello,
I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020.
Can...HORSTE — 10:32 AM |
|
Philco 42-1008 conversion kit
|
| I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit. That would rem...alangard — 09:30 PM |
|
HiFi (Chifi) tube amp build - but my own design.
|
| Tim
Well...a chassis is metal. Magnetic or not, it does not matter.
A transformer has some hum to it. It is natural. Th...morzh — 08:40 PM |
|
Hickok AC51 tube tester
|
| I thought the 83 tube was bad because it looked white but it tests strong. Blue gassy though. I checked the fuse, it was...martinj — 08:37 PM |
|
Shadow Meter Bulb
|
| Ross
I am not sure what current limiting effect the incandescent provides.
They are two different parts of the sch...morzh — 08:31 PM |
|
Who's Online
|
There are currently 5846 online users. [Complete List]
» 1 Member(s) | 5845 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
