Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

NOOB here- how to set push buttons on model 39-45
#1

Hi everyone,  thanks for letting me join this site . When I was growing up in the 1950's my parents had a model 39-45 we listened to every day. Now here I am 65 years later and have finally finished its restoration. I'm trying to figure out how you set the push buttons. Does it require changes in the chassis or is there a way for the user to set them?  Also,  can I post a picture here?

Thanks,
Warren
#2

Hi and welcome,
The info the here in the service manual: http://www.nostalgiaair.org/Resources/298/M0013298.htm
There are two adjustments for each push button. One sets the osc and the other adjusts the ant circuit.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Welcome to the Phorum!

Yes you can post photos. See:
https://philcoradio.com/phorum/showthread.php?tid=29
#4

Welcome to the phorum!  Lots of very helpful pholks here to assist any way they can.  Take care, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#5

Anyone know how or where to get new station labels?
#6

https://philcoradio.com/phorum/showthread.php?tid=5148

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently 6820 online users. [Complete List]
» 1 Member(s) | 6819 Guest(s)
Avatar

>