Posts: 7
Threads: 2
Joined: Dec 2010
I've finally finished rebuilding a Philco 40-180 for friend who obtained the radio from his grandfather. I replaced all paper and electrolytic caps, rubber wire and gave it a good cleaning. It sounds great for a 1940 vintage radio.
I tried to keep it as original as possible that is why the original electrolytic's are still in place but are disconnected below.
The cabinet was in great shape to begin with so I just treated it with Howard's "restor a finish" and "feed n wax". I was going to refinish the metal trim around the dial but wanted to get it to my friend before Christmas. Anyone know who sells Plasti kote #139S brass paint locally?
Attached are a few before and after photos.
[Image:
http://img94.imageshack.us/img94/934/img0057gz.jpg]
[Image:
http://img442.imageshack.us/img442/4104/img0064zz.jpg]
[Image:
http://img10.imageshack.us/img10/8822/img0159ya.jpg]
[Image:
http://img69.imageshack.us/img69/8769/img0164vv.jpg]
[Image:
http://img96.imageshack.us/img96/191/img0165ub.jpg]
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
Nice looking set! I did a 41-280 for my brother last summer when I went home for a month. Agree, a swell sounding radio!!
How do you like the Howards products? I have heard a lot about the resto-finish product, but have not convinced myself to try it yet.
Posts: 7
Threads: 2
Joined: Dec 2010
I like the Howard products, they are very easy to apply and do a great job. They are discussed in the Cabinet Restoration section often.
I don't normally restore radio's, I mainly do tube equipment for stereos. I have a Dynaco ST 70 amplifier and Dynaco PAS 2 pre-amp that I recapped and use as part of my 2 channel stereo system. I have plenty of projects but little time to work on them. I have my Dad's first "hi-fi" which is an old Philco with a built in record player that I would like to restore on day.
I decided to paint the metal trim around the dial on the 40-180 since it looked worn compared to the rest of the radio.
Posts: 7
Threads: 2
Joined: Dec 2010
Updated pics with the newly painted bezel and a second coat of wax. I used Rust-oleum aged brass paint #254452.
[Image:
http://img375.imageshack.us/img375/8436/img0172m.jpg]
[Image:
http://img146.imageshack.us/img146/8904/img0173hv.jpg]
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
Very nice!!!
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 20
Threads: 7
Joined: Jan 2011
The radio chassis and escucheon design look like my 39-31 Philco. I am looking for an antenna and speaker for this model. Can you help? By the way what is the part number for the 8 buttons? Nice restoration!!
Thx,
Jimy
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
The 39-31 did not have a built-in antenna. It relied upon an external longwire antenna.
--
Ron Ramirez
Ferdinand IN
Posts: 20
Threads: 7
Joined: Jan 2011
Ron,
Any long wire will due, or do I have to find a wire from that era and model?(39-31) I have a stereo radio Y wall wire that I thought might do the trick?
Jimy
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Any sort of insulated wire will do.
The 39-30, as with all vintage radios designed to use longwire antennas, was designed to work best with a longwire erected outdoors, 50 to 100 feet in length, as high off the ground as possible and as far away from electrical lines as possible. Such a longwire must have lightning protection by the use of a lightning arrestor.
Today, it is not always possible or practical to erect an outdoor longwire. A length of insulated wire, 20 or so feet long placed in the same room as the radio is in, is better than nothing. Be sure the far end of the wire (the end not connected to the radio) is not connected to anything and cannot be placed into a nearby electrical outlet by a child!
--
Ron Ramirez
Ferdinand IN
Posts: 20
Threads: 7
Joined: Jan 2011
Thanks Ron, you are truly a wealth of knowledge willing to share without hesitation!!
Thanks again,
Jim
Posts: 7
Threads: 2
Joined: Dec 2010
Jimy Wrote:The radio chassis and escucheon design look like my 39-31 Philco. I am looking for an antenna and speaker for this model. Can you help? By the way what is the part number for the 8 buttons? Nice restoration!!
Thx,
Jimy
I purchased the 8 buttons from Radio Daze (radiodaze.com), the part number is PB-PHIL41-B. With shipping they were around $20.
Posts: 438
Threads: 15
Joined: Jul 2008
City: Anacortes, WA
What color did you use? I was under the impression that the buttons were originally wine-colored, but those look to be brown.
Posts: 7
Threads: 2
Joined: Dec 2010
DeckApe Wrote:What color did you use? I was under the impression that the buttons were originally wine-colored, but those look to be brown.
You are correct I used the brown buttons. I believe that only the early builds used the wine colored buttons. The original buttons were wine colored but it was hard to tell when I received the radio since they were in poor shape. Radio Daze sells the wine colored buttons as well.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
All of the 1940 Philco models with eight pushbuttons used wine colored translucent buttons. Philco switched to brown for the 1941 models.
--
Ron Ramirez
Ferdinand IN
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
