Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

What do I have...
#1

I was given this old Philco cathedral radio and am trying to find out the model and year it was made if possible. There are no markings on the chassis or wooden case that I can see. I hope the pics will tell the story.

I'm sure you guys know...right?

Note from site admin: Sorry, but the photos which were attached to this post are no longer available.

Best regards,
Kico

"I whisper, but my horse still doesn't listen."
#2

Hello, and welcome!

You have a Model 84B, the late version from January 1936:

http://www.philcoradio.com/gallery/1936b.htm#c

That is an oversized power transformer. Might be a 25 cycle model? If so, it will work on today's 60 cycle line current.

--
Ron Ramirez
Ferdinand IN
#3

Thanks Ron,

I tested all the tubes and they all check good. I then fired it up on my dim bulb tester...as expected a very loud 60 cycle hum but no smoke Icon_smile...faulty power supply cap I suspect.

Any good links here on the forum for rebuilding one of these?

Thanks again...

Best regards,
Kico

"I whisper, but my horse still doesn't listen."
#4

You may want to search this site for similar models like model 80,84,600, 57,37-84.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

7estatdef Wrote:You may want to search this site for similar models like model 80,84,600, 57,37-84.
Terry

Thanks Terry,

Whew...there's a lot here. I was wondering if anybody has compiled a component list (caps/resistors, etc.) needed for rebuilding an 84B they could post or send me? My eyes are not what they used to be, and reading the actual and schematic values is difficult. I'd like make sure I have the correct parts before I place an order.

Also, could someone on the forum link me to the correct schematic for this radio...thanks.

Best regards,
Kico

"I whisper, but my horse still doesn't listen."
#6

May I suggest you contact Chuck Schwark to obtain the service information package for this radio, which will include an 11 x 17 enlarged schematic, parts list, alignment info, changes, etc., etc.

http://www.philcorepairbench.com/schematics.htm

Well worth the nominal fee.

--
Ron Ramirez
Ferdinand IN
#7

Thanks Ron...I'll do it!

Best regards,
Kico

"I whisper, but my horse still doesn't listen."
#8

Hi Ron,
I am working on one of these right now, the exact same cabinet. But the inside label says it's just a model 84. Does the 84B just refer to the style of cabinet, and is not marked so on the blue tag?
I do have another 84 but with the more circular cabinet.

Kico, I posted some photos an info for you on your other thread.

Thanks. Gary.
#9

Hi Gary

Yes, the "B" referred to the style of cabinet; in this case, "B" = Baby Grand - which is how Philco referred to its cathedrals and tombstones back then. The terms "cathedral" and "tombstone" did not come into general use until decades later, as people like us began to collect these radios.

The sticker on the back of the chassis will read "CHASSIS TYPE 84" without mentioning the cabinet style.

--
Ron Ramirez
Ferdinand IN
#10

Thanks Ron, that clears up the mystery.

Working on the cabinet today, shouldn't be too bad. No veneer or photofinish to worry about.

Take care,
Gary




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5645 online users. [Complete List]
» 1 Member(s) | 5644 Guest(s)
Avatar

>