1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 48-1262 restoration
MatthewG
Junior Member
**
Posts: 3
Threads: 1
Joined: Dec 2019
City: Kirkland State, Province, Country: WA
#1

12-30-2019, 10:08 PM
My wife recently inherited a model 48-1262. The radio works great. The phonograph not so great. 

There’d is no sound being transmitted from the phonograph to the speaker. We can hear music at the actual needle but nothing coming out of the speaker.

We are new to old radios and have no idea where to start in trouble shooting this. All wires appear to be in place. I’m not sure if this is more likely to be a wiring issue or a bad capacitor or tube.
Find
Ed Locker
Member
***
Posts: 204
Threads: 5
Joined: Sep 2005
City: Newark, Ohio
#2

12-31-2019, 11:11 AM
It most likely has a dead cartridge.
Find
GarySP
Super Moderator
******
Posts: 1,976
Threads: 147
Joined: Jan 2013
City: Westland, MI
#3

12-31-2019, 11:48 AM
+1 what Ed said. Also shouldn't be powered up before caps and all out of range resistors are replaced. Welcome to the phorum! Take care, Gary
"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#4

12-31-2019, 01:32 PM
Welcome to the Phorum!
Icon_wave
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
MatthewG
Junior Member
**
Posts: 3
Threads: 1
Joined: Dec 2019
City: Kirkland State, Province, Country: WA
#5

12-31-2019, 09:57 PM
Thanks. So I don’t even know enough to know what a cap or an “out of range” resistor is. Where is a good starting place to get some base knowledge?
Find
MatthewG
Junior Member
**
Posts: 3
Threads: 1
Joined: Dec 2019
City: Kirkland State, Province, Country: WA
#6

12-31-2019, 10:10 PM
Here are photos of the radio. I have cleaned the cobwebs out of it and done some dusting but it looks pretty much untouched.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently 4966 online users. [Complete List]
» 2 Member(s) | 4964 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration