1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 48-1262 restoration
MatthewG
Junior Member
**
Posts: 3
Threads: 1
Joined: Dec 2019
City: Kirkland State, Province, Country: WA
#1

12-30-2019, 10:08 PM
My wife recently inherited a model 48-1262. The radio works great. The phonograph not so great. 

There’d is no sound being transmitted from the phonograph to the speaker. We can hear music at the actual needle but nothing coming out of the speaker.

We are new to old radios and have no idea where to start in trouble shooting this. All wires appear to be in place. I’m not sure if this is more likely to be a wiring issue or a bad capacitor or tube.
Find
Ed Locker
Member
***
Posts: 204
Threads: 5
Joined: Sep 2005
City: Newark, Ohio
#2

12-31-2019, 11:11 AM
It most likely has a dead cartridge.
Find
GarySP
Super Moderator
******
Posts: 1,976
Threads: 147
Joined: Jan 2013
City: Westland, MI
#3

12-31-2019, 11:48 AM
+1 what Ed said. Also shouldn't be powered up before caps and all out of range resistors are replaced. Welcome to the phorum! Take care, Gary
"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#4

12-31-2019, 01:32 PM
Welcome to the Phorum!
Icon_wave
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
MatthewG
Junior Member
**
Posts: 3
Threads: 1
Joined: Dec 2019
City: Kirkland State, Province, Country: WA
#5

12-31-2019, 09:57 PM
Thanks. So I don’t even know enough to know what a cap or an “out of range” resistor is. Where is a good starting place to get some base knowledge?
Find
MatthewG
Junior Member
**
Posts: 3
Threads: 1
Joined: Dec 2019
City: Kirkland State, Province, Country: WA
#6

12-31-2019, 10:10 PM
Here are photos of the radio. I have cleaned the cobwebs out of it and done some dusting but it looks pretty much untouched.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3796 online users. [Complete List]
» 1 Member(s) | 3795 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration