Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

IDENTIFICATION PT50 or TH14 ??
#1

Hi, I am new on this forum!
Found recently this one, very poor condition.
Probably PHILCO PT50 Transitone (1940) or may be TH14.(seems same line up)
If PT 50, rear coil waxed for "tropicalisation" ? and why these turns in both directions
perpendicular ?
Someone could give precisions please ?

And for building new cabinet, I am looking for a good photo of the box.

Thanks for help.
megawave
French collector

[Image: http://img638.imageshack.us/img638/9291/...50face.jpg]

[Image: http://img339.imageshack.us/img339/702/philcodessus.jpg]

[Image: http://img836.imageshack.us/img836/1585/...bottom.jpg]

[Image: http://img407.imageshack.us/img407/1162/...tcopie.jpg]
#2

Looking at the service bulletins for both 1940 models, the schematics are the same (except for one additional cap in the TH-14. The other components have slightly different values as well, but schematic is virtually identical.
Tube complements are also the same.
The big differences are dial plates, and wood (TH-14) or bakelite (PT-50) cabinets.

So, it appears you have a chassis out of a TH-14 or TH-16, due to he dial face.

Chuck
#3

Hi Chuck, thank you for infos; I have a picture of PT50, (found on Ron's site, see below) but it is WOOD cabinet. Do you know what was the look of bakelite cabinet for this one ?
Thanks
megawave
Icon_smile
French collector


[Image: http://img703.imageshack.us/img703/3645/...50wood.jpg]

Uploaded with ImageShack.us
#4

No I don't a picture. I believe it is similar to the PT-47/PT-51, but with out the pushbuttons.

Ron can correct me here if I'm wrong.

Chuck
#5

OK Chuck, thanks for reply, all is clear now. (Seen also your reply on Antique radio forum.)
Photos on line when job finished. Icon_smile
Sincerely,
megawave
French collector
#6

Hello Megawave,

Just so happens I have a PT-50 cabinet. Icon_smile If you need detailed photographs and dimensions, please contact me.

I agree with Chuck that you have a TH-14 or TH-16 chassis, due to the design of the dial face.

Just for fun, here's what they look like.

TH14: http://www.philcoradio.com/gallery/1939c.htm#m

TH16: http://www.philcoradio.com/gallery/1940a.htm#bn

I find it interesting that the TH-14 was advertised as a (January) 1939 model, yet it is not in the 1939 Philco RMS Yearbook - it is in the 1940 RMS Yearbook. Icon_confused: Icon_confused

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>