Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Puzzled -40-180
#1

What's happening here? The 6 meg tone control (51) is switched. That's why the dotted line. But the wiper can't be grounded, or the .01 cap, 40a, would just be shorted to ground. Why does the wiper have a circle for connection, instead of a dot? It appears the actual pot has nothing connector to the wiper.  How does this tone control work?

I'm confused.

[Image: https://i.imgur.com/e9jYt0n.jpg]
#2

It is correct.
The wiper simply brings GND closer to the C50,  cutting out the treble, or further away, letting the treble through.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Got it. I'm getting old. I guess.
#4

Well I have a question too! where does the phase inversion come from for the push pull? Does it come from the screen grid of the upper 41, through the .01 cap #52?
#5

Yup...

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#6

This is called "Paraphase inverter".

It is described here.


https://dalmura.com.au/static/Phase%20In...201948.pdf


Look at Fig. 10.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#7

Thanks guys! I like the line "results are disappointing..." I would think there would be some phase problems between the 2 output tubes, but I've never played with the circuit.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM
40-150 General questions
I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM
Philco 38-7 Speaker
FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM
Philco 38-7 Speaker
Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM

[-]
Who's Online
There are currently 2602 online users. [Complete List]
» 1 Member(s) | 2601 Guest(s)
Avatar

>