1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Finally out of the attic!!!
43ddoc
Junior Member
**
Posts: 7
Threads: 2
Joined: Oct 2018
City: bartlett State, Province, Country: TN
#1

08-16-2020, 11:14 AM
    Well guys, I finally pulled this beauty out of the attic with a little help. Managed to not damage it getting it down. Everything seems to work!! The tube take a couple minutes to warm up and the speakers have explosions of sound quite a bit while tuning and adjusting the volume but the sound does come through at low levels. If anyone has any advice on components that should be preemptively replaces to ensure the set keeps operating or any tips in general, I would sure appreciate it.                
(This post was last modified: 08-16-2020, 01:31 PM by 43ddoc. Edit Reason: Add picture )
Find
GarySP
Super Moderator
******
Posts: 1,974
Threads: 147
Joined: Jan 2013
City: Westland, MI
#2

08-16-2020, 11:21 AM
First tip ... DO NOT plug it in again until you replace capacitors and any out of spec resistors. Plugging in a set full of old components is just asking for disaster to happen. By the way, what model are you commenting about ... no photos are attached. Take care and BE HEALTHY! Gary
"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
Find
43ddoc
Junior Member
**
Posts: 7
Threads: 2
Joined: Oct 2018
City: bartlett State, Province, Country: TN
#3

08-16-2020, 11:25 AM
    Well guys, I finally pulled this beauty out of the attic with a little help. Managed to not damage it getting it down. Everything seems to work!! The tube take a couple minutes to warm up and the speakers have explosions of sound quite a bit while tuning and adjusting the volume but the sound does come through at low levels. If anyone has any advice on components that should be preemptively replaces to ensure the set keeps operating or any tips in general, I would sure appreciate it.            
(This post was last modified: 08-16-2020, 01:34 PM by 43ddoc.)
Find
43ddoc
Junior Member
**
Posts: 7
Threads: 2
Joined: Oct 2018
City: bartlett State, Province, Country: TN
#4

08-16-2020, 11:29 AM
I’m trying to attach photos but they don’t seem to load.
Find
43ddoc
Junior Member
**
Posts: 7
Threads: 2
Joined: Oct 2018
City: bartlett State, Province, Country: TN
#5

08-16-2020, 11:35 AM
Original post
https://philcoradio.com/phorum/showthrea...#pid146422
Find
klondike98
Phorum Moderator
******
Posts: 5,084
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#6

08-18-2020, 01:03 PM
I merged your two "Finally out of the attic" posts together.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#7

08-18-2020, 03:27 PM
As Gary said replace the capacitors. It's probably new enough that it most are going to be ceramic. On the other hand the eletrolytic caps should be replaced if they haven't been in the last 20yrs or so. The picture of the screen tells me that there maybe an issue with the power supply as the raster isn't filling the screen. Definitely would measure the hv at the p/s and the boost line to see if it is within reason.

GL
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
PhilcoJohn
Phorum Expert
*****
Posts: 1,463
Threads: 97
Joined: Jul 2012
City: Poughkeepsie, N.Y.
#8

10-08-2020, 06:36 PM
Wow nice unit! As Gary said do not plug it in again before you or someone else goes  through the whole console. You do not want to burn it up.  Icon_e_sad
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4622 online users. [Complete List]
» 1 Member(s) | 4621 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration