Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
Without going into too much detail, I can inject an RF signal at various frequencies down to 500Hz (with var. cap fully meshed), and tune to that frequency, at which point I can adjust both the 1st and 2nd IF cans. But I get nothing when I try to inject the 460 Hz IF.
Can something be preventing me from hearing anything below 500Hz? Only tried it by ear so far.
I'll post a schematic if needed, but I thought this just might be a general question.
Thanks.
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Do you mean hz or khz?
Would connect the generator to the grid cap of the 6A7 and set it for 460kc w/modulation. Adjust IF transformers for max signal. If there is no signal check voltages at the plate and screen of the 6A7 and 78.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 04-02-2021, 12:01 PM by Radioroslyn.)
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
Khz. Cap of 6A7 is where I fed the signal in. No IF. Voltages are good. Can receive stations.
(This post was last modified: 04-02-2021, 12:08 PM by Patrick.)
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Ok voltages @ the 6A7 and 78?
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
So the problem is you can't align the IF but the receiver works?
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
Yes. Well...I can align by using an existing station, but not using the IF frequency. And I know my sig gen works.
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Ok sounds like a generator problem. Would check by listening for the 2nd harmonic of 460kc (920kc) on a modern digital receiver. Don't know what you are using but could have a dirty band switch or out of alignment on that band.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
Nope. I'm using an HP 8657A. Tried it on other chassis. Works fine. 'Tis a mystery.
Posts: 16,250
Threads: 564
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Are you sure 6A7 is good?
Increase your IF signal a whole lot if possible.
Make sure your cap on your 6A7 soldered well.
Check IF coils for continuity.
Try bypassing 6A7: inject the 460kHz right into the IF xfmr (6A7 plate) via a capacitor and put a Zener in parallel to the generator output to protect it from initial surge of Plate voltage.
PS. Have you UNPLUGGED the Grid Cap wire from 6A7 Grid Cap? If not, it should be unplugged.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
Yeah, I tried 2 other 6A7's. First thing I did was check the IF coils. One thing that was puzzling, is that the primary of the second IF should be 11.5Ω, but it measures 39Ω. Pulled the can off, and everything LOOKS fine, but still 39Ω. All the other coils are spot on. Haven't bypassed the 6A7 yet.
Posts: 16,250
Threads: 564
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
But you did disconnect the wire to the 6A7's cap when applying the signal to the cap?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
Posts: 16,250
Threads: 564
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
I cannot explain it.
If it were not disconnected, there is the wavetrap. It attenuates 460kHz.
If you used good high levels of 460kHz and it does not show at he output, I would disconnect the filters and put the signal directly through them, trying to align them to it.
Keep the input is under the plate voltage, so if using a solid state generator, use a capacitor and a zener in parallel to the generator's output (i use it all the time, I described it a few years ago.)
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 16,250
Threads: 564
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
How sure are you your generator is good?
I am asking because if you used it to align other radios it will work with them then.
Do you have a counter that could confirm the accuracy of 460kHz?
Also, is it possible you simply have not found the spot in the IF cans where the signal would go through? It could be simply really badly out of IF alignment, so one of the filters would always block it.
I think now even more, it is time to disconnect the filters and align them one by one; start from 27 first, then solder it back and align the 21.
then try to inject the 460kHz via the 6A7's cap.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Users browsing this thread: 3 Guest(s)
|
|
Recent Posts
|
|
Philco 91 Restore Code ??
|
| I knew that Fluke was the Cadillac so with that in mind what Fluke would you recommend I get?dconant — 03:53 PM |
|
Philco 91 Restore Code ??
|
| Yep. 10W is probably enough.
Also, if the meter measures Farads, then it should also have that "Delta" button...morzh — 02:38 PM |
|
Philco 91 Restore Code ??
|
| I measured the current through the resistor I am using as a replacement for the speaker field coil and got 40ma. So that...dconant — 02:32 PM |
|
Philco 91 Restore Code ??
|
| No I'm not saying I don't own a DMM. I have a CCC one (Thsinde 18+). I forgot that could read caps. I did purchase a Flu...dconant — 02:28 PM |
|
Philco 91 Restore Code ??
|
| Are you telling me you do not own any decent DMM, that can measure capacitances from a few pF and up? Even todays CCC (C...morzh — 01:44 PM |
|
Restoring Philco 96
|
| Well, selectivity today, with stations disappearing, is not such a problem for TRF as it likely used to be.
Although wh...morzh — 01:42 PM |
|
Philco 91 Restore Code ??
|
| Mike I did that already and can't really get any kind of reading. My little Honeytek A6013L reads 0 on all scales. One s...dconant — 01:38 PM |
|
New member
|
| Well, to be frank, when it comes to radios, especially the older types, a person with no electronic background could be ...morzh — 01:33 PM |
|
Restoring Philco 96
|
| Thanks for mentioning the video you had uploaded. Somehow I missed that post. Just watched your video, and it sounds to ...jrblasde — 01:28 PM |
|
Restoring Philco 96
|
| Joseph
well, for now we will have to get by the video I have made, as the final video would not be made before I get a ...morzh — 01:04 PM |
|
Who's Online
|
There are currently 4712 online users. [Complete List]
» 3 Member(s) | 4709 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
