1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
philco 60 -505
denver
Member
***
Posts: 217
Threads: 40
Joined: Dec 2009
#1

04-06-2011, 06:53 PM
Been awhile ... but i found a nice 60- 505.
When i go to Nostalgia air ... would i go to model 60 for schematics?
Thanks for any info.
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#2

04-06-2011, 07:03 PM
Yes, you will find it listed there under Model 60.

http://www.nostalgiaair.org/Resources/793/M0013793.htm

Don't forget, Model 60 underwent numerous changes during its nearly three year production run. All of the changes are documented here:

http://www.philcoradio.com/tech/60evol.htm
--
Ron Ramirez
Ferdinand IN
Find
denver
Member
***
Posts: 217
Threads: 40
Joined: Dec 2009
#3

04-06-2011, 07:05 PM
Your the man thanks a bunch. Icon_thumbup
Looked mine is the 60b 1936
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#4

04-07-2011, 06:37 PM
Hi Denver
If this old gal gives you trouble double check the oscillator coil they can be a problem on this model.
Good luck w/it
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
denver
Member
***
Posts: 217
Threads: 40
Joined: Dec 2009
#5

04-08-2011, 09:46 AM
Will probably wait till .. winter again to work on.
Get me another or two.. have some projects for cold season.
Order tubes ect. have everything ready.
Thanks for info. Icon_wink
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM
38-10T chassis Restoration begins
I have a question about the mica sheets. I thought I saw somewhere on the Phorum where someone used thin plastic report ...dconant — 10:44 AM
38-10T chassis Restoration begins
Yes, you should carefully remove the mica sheets from the trimmers otherwise you risk trapping foreign material in the t...RodB — 10:34 AM
American Bosch Model 802 auto radio
Hi Joe, Thank you again. The American Bosch Model 634A has the same tube lineup as my Model 802 and the parts layout dia...Antipodal — 03:09 AM

[-]
Who's Online
There are currently 3365 online users. [Complete List]
» 5 Member(s) | 3360 Guest(s)
AvatarAvatarAvatarAvatar
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration