Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philcos all aglow gather here

I used to sit with my grandfather back in the early 1950s and listen to a set like this 48-1270. That glowing dial was etched in my memory and was the inspiration for restoring this set.    

It is essentially the same cabinet as 46-1213 I recently finished.
Same dial too.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.

BigRedDog, that is a great looking radio/phonograph. Looking at the dial and knob arrangement I am reminded of the 48-482, which is a table radio. I have restored one, and have a couple of others yet to restore. It is one of my favorite Philcos although the FM can be a bit of a pain to get squared away. This is what the 48-482 looks like. If you took the same chassis, and turned it on its side, I think you would have a very similar result to your 48-1270. Basically the same radio just added the phonograph to it. Look at the dial, even the numbering is the same, just turned 90 degrees.
[Image: https://64.media.tumblr.com/d640415209ad...2_1280.jpg]

Mikethedruid that cabinet looks flawless - beautiful! My wife had wondered why the 1270 dial and controls are angled inward. I told her it was just aesthetics, but you have the real reason.
Interesting how major components are shared among various models. Radios are a lot like cars I suppose. As morzh points out the 1270 (1216) model persisted across multiple years. I would like to know more about the marketing, engineering, and aesthetic design processes and decision making that occurred through the years.

I finished my Philco model 66 from 1935. Here is a close up of the dial all aglow...

[Image: https://64.media.tumblr.com/67925b51f630...856b7e.jpg]

Good morning, here's a picture of the dial on my Philco 47-1230 I finished restoring last month--listening to WJR.   Ken


Attached Files Image(s)
   

Very nice, Ken, congratulations. Icon_thumbup

Hello BigRedDog,
what great looking set !
mike that 48-482 looks really nice .
Ken sounds like your set came out working well for you then .

Sincerely Richard

Hello everyone, here's the dial aglow on my Philco 38-10XF that I got back into restoring yesterday. I'm currently listening to WLW on it.   Ken


Attached Files Image(s)
   

Enjoyed all the previous postings!!!  Here's my lineup....
Hope I don't get "Reported" for showing "non-Philcos"
1st...Philco 48-482
2nd...The Spice Chest Radio "spices not included"
3rd & 4th...Grebe AH-1


Attached Files Image(s)
               

They all glow nice, Philcos or not.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.

Icon_thumbup Icon_thumbup Icon_thumbup




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3943 online users. [Complete List]
» 1 Member(s) | 3942 Guest(s)
Avatar

>