1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
41-605 Squeal/Motorboat
glwells
Junior Member
**
Posts: 15
Threads: 5
Joined: Aug 2009
City: Columbus State, Province, Country: NC
#1

10-28-2021, 08:17 PM
I'm working on a 41-605, replaced the obligatory caps as well as some dominos, out of spec resistors, checked tubes, general socket and pot cleanups, etc. The AM side plays fine up to about 1400 where the oscillator starts the infamous squeal and motorboating right up thru the top of the dial. All good below 1400. The SW side works fine with no issues. I have it isolated to most likely issues with the oscillator circuit. A NOS 14AF7/XXD didn't help. Resistance specs of the oscillator coil are good. I've maneuvered lead and component placement as much as I dare in the oscillator area around the XXD. Oscillator padder 17A does impact the intensity but doesn't eliminate it. Can anyone offer any suggestions or hints as to what I may have missed?

Much appreciated.

Gary
WB9AYD
Website Find
vinzer
Member
***
Posts: 214
Threads: 16
Joined: May 2010
City: Kokomo, IN
#2

10-29-2021, 11:31 AM
Are all tube shields on?
Find
glwells
Junior Member
**
Posts: 15
Threads: 5
Joined: Aug 2009
City: Columbus State, Province, Country: NC
#3

10-29-2021, 12:12 PM
These are Loctals and I cleaned all of the tubes and sockets.
Website Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM
Philco Predicta Siesta picture over time getting dimmer
I found that the wire insulation was burnt.  The fly back needs corona dope! Why would someone put that there?Platinumblonde36 — 01:09 AM

[-]
Who's Online
There are currently 5095 online users. [Complete List]
» 1 Member(s) | 5094 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration