Posts: 804
Threads: 42
Joined: Dec 2008
City: Chicago, IL
That coil was open in both chassis. Same old issue. primary wound over a celluloid insulator that had hardened and warped.
Luckily, the break was easy to find and repair. I did not need to rewind 
[Image: https://live.staticflickr.com/65535/5163...6f90_c.jpg]
Yep, that fixed it. It must have been barely hanging on and would open up when it got warm.
Posts: 1,731
Threads: 110
Joined: May 2008
City: Omak
State, Province, Country: WA
Hello Bob,
That is great news now the radio should work fairly well !
Sincerely Richard
Posts: 804
Threads: 42
Joined: Dec 2008
City: Chicago, IL
I performed a minor surgery on the Philco 20 PP speaker I have so that the field coil is connected to one end of the OT primary rather than the center tap.
[Image: https://live.staticflickr.com/65535/5164...3df9_c.jpg]
Viola - it works. Sounds a little hollow and dull, but it works fine. I'll use it for now until I can get the 90 speaker field coil repaired.
[Image: https://live.staticflickr.com/65535/5163...032d_c.jpg]
(This post was last modified: 10-29-2021, 05:03 PM by Bob Andersen.)
Posts: 16,259
Threads: 566
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Unless I missed it - does the field coil work now?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 804
Threads: 42
Joined: Dec 2008
City: Chicago, IL
I have two speakers. A single ended one for a Philco 90 with an open field coil and missing output transformer.
The one shown above is for a Philco 20 with push-pull 71A driving it. I disconnected the center tap and tied one end of the output transformer to one side of the field coil to make it compatible with my 90.
Posts: 1,731
Threads: 110
Joined: May 2008
City: Omak
State, Province, Country: WA
Hello Bob,
good thinking far as the speaker goes !
sincerely Richard
Posts: 4,810
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
I found a cheaper source of magnet wire, can't vouch for the seller of course: https://www.ebay.com/itm/363090262105
Regards
Arran
Posts: 804
Threads: 42
Joined: Dec 2008
City: Chicago, IL
Thanks for the tip. I just placed an order.
I'll try the techniques described in this thread to get the pole piece out and back in.
https://philcoradio.com/phorum/showthread.php?tid=15792
(This post was last modified: 11-03-2021, 01:12 AM by Bob Andersen.)
Posts: 804
Threads: 42
Joined: Dec 2008
City: Chicago, IL
Hey, finally found a currently made audio taper 500K pot with a 2" round shaft. 2W rating.
Not exactly cheap at $17.76, but at least there's an option from a decent brand. Shaft can be cut or filed down as needed.
https://www.mouser.com/ProductDetail/CTS...364R504A21
Also available from Digi-Key for a bit more.
https://www.digikey.com/en/products/deta...1/11617375
(This post was last modified: 11-03-2021, 10:35 PM by Bob Andersen.)
Posts: 1,731
Threads: 110
Joined: May 2008
City: Omak
State, Province, Country: WA
Hello bob,
man I wish you were not in a hurry because when i visit my family in dec. i could check my NOS stock of controls .
sincerely Richard
Posts: 804
Threads: 42
Joined: Dec 2008
City: Chicago, IL
Oh, I'm not in any particular hurry. I might very well have one in my stash too. I've seen many radios with a replacement volume control of the wrong value or taper type. It's nice to have options.
Posts: 804
Threads: 42
Joined: Dec 2008
City: Chicago, IL
Magnet wire arrived today. Looks like the real deal. We'll soon find out how well it works.
[Image: https://live.staticflickr.com/65535/5165...512d_c.jpg]
Posts: 1,731
Threads: 110
Joined: May 2008
City: Omak
State, Province, Country: WA
Hello Bob,
that is great news I do have some but I don't think that gauge thou.
I have a new project to rebuild a huge RCA like 10 tube count chassis with the magic brain .
Sincerely Rich
Posts: 285
Threads: 27
Joined: Nov 2012
City: Tehachapi. California
I wish I had a magic brain. Mine is always thinking the wrong thing.
!!!!!!!!!!!!!!!!!!!RESISTANCE IS FUTILE!!!!!!!!!!!!!!!!!!!!!!
/\/\/\/\/\/\/\/\/\
[Image: http://philcoradio.com/phorum/images/smi...on_eek.gif] Chris
Posts: 804
Threads: 42
Joined: Dec 2008
City: Chicago, IL
The new volume control has arrived and works very well. Perfect fit too.
It's just temporarily wired in here as I still need to cut the shaft down.
[Image: https://live.staticflickr.com/65535/5166...9f2f_c.jpg]
I also installed the new arch support. Before gluing I painted with this very flat camo paint. It's a great match for the old dark interior wood.
[Image: https://live.staticflickr.com/65535/5166...c0c1_c.jpg]
The arch is far stronger now and that's a big load off my mind.
Sorry about the blurry photo. Bad lighting in the basement.
[Image: https://live.staticflickr.com/65535/5166...ef6f_c.jpg]
(This post was last modified: 11-10-2021, 02:22 AM by Bob Andersen.)
Users browsing this thread: 4 Guest(s)
|
|
Recent Posts
|
|
An attempt to remove the Field Coil from a G speaker
|
| Hi Morzh,
May be a good idea to remove the cone to prevent damage. You may have to do so anyway to remove the pole ...MrFixr55 — 08:44 PM |
|
Philco 91 Restore Code ??
|
| I think that Danaher, the company that owns Beckman-Coulter (the company that I worked for 41 years) owns Fluke. They a...MrFixr55 — 08:35 PM |
|
Philco 91 Restore Code ??
|
| Rod
I wish... :lol:
I am not sure I'd buy the Fluke, had it not fell in my lap for free. $500 to $800...it's a lot...morzh — 08:09 PM |
|
Philco 91 Restore Code ??
|
| Mike, ...you get a commission?RodB — 07:52 PM |
|
New member
|
| Hi. I specialize in refurbishing Predictas, but I'm in Chicago. If you can get it to me, I'd be happy to go over it. ...Bob Andersen — 06:43 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| I have 3 G speaker, all with open Field coils.
Today I pull one of the shelf and decided to try to remove the FC (spo...morzh — 06:07 PM |
|
Philco 91 Restore Code ??
|
| Thanks Mike. I will check them out.dconant — 05:52 PM |
|
Philco 91 Restore Code ??
|
| There is no such thing as bad Fluke.
This said, they are expensive. A Fluke is easily 10x the price of comparable CCC...morzh — 05:45 PM |
|
Philco 91 Restore Code ??
|
| Hello Mike,
Yes, I have 3 Fluke meters one being my first Fluke 77 and other being Fluke 87.
My third is Fluke clamp -...radiorich — 05:04 PM |
|
Philco 91 Restore Code ??
|
| I knew that Fluke was the Cadillac so with that in mind what Fluke would you recommend I get?dconant — 03:53 PM |
|
Who's Online
|
There are currently 3805 online users. [Complete List]
» 1 Member(s) | 3804 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
