Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 60 troubles
#1

I am working on an earlier model 60 (pre wave trap).  I have replaced all the caps and a few our of spec resistors.  All the tubes test good (and I have also swapped tubes from a working 60).  The speaker, output transformer, and assoicated wiring is good (I also swapped a working speaker and related parts from a working 60.)  The set powers up, and with an antenna attached will receive stations along the entire dial, but the volume is a whisper.  The volume control works and will take the volume from 0 to a whisper.  The volume pot is good and I also swapped a working pot from another radio with the same results.  Touching the volume pot connections does not produce a buzz or hum.  I am at a loss.  I compared voltages to the working 60 and nothing iappears to be alamingly different.  Since it receivce stations does that mean the various transformer coils are ok?

Ideas?
#2

Would check the grid wire on the 75 to see if there is a short where it goes thru the chassis. Low plate voltage on the 75  will cause it. If all the voltage are good I would recheck the wiring of the replaced parts. Are all of the blocks wired correctly inside and out? I've miswired the coupling caps before and had the same results. GL.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

No short located on the 75 tube grid wire. Question regarding voltages. Should you use the chassis or the “K” pin on the tube? Would an open or compromised antenna transformer cause this issue?




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

[-]
Who's Online
There are currently 6155 online users. [Complete List]
» 1 Member(s) | 6154 Guest(s)
Avatar

>