Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 16B
#1

Looking for a readable schematic and parts list .. copies i have are very hard to read. this one uses a 80 rectifier tube

[Image: https://live.staticflickr.com/65535/5189...88b7_k.jpg]

[Image: https://live.staticflickr.com/65535/5189...ba34_k.jpg]


Thanks

Skip
#2

https://philcoradio.com/library/download...l.%201.pdf
It's a code 121.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Thanks Terry, Have you ever worked on this model?

There is a hole on right side of cabinet.. Was that factory? If so what went there?

Skip
#4

Vecher, if you look in the gallery of the main site,  https://philcoradio.com/gallery2/1933b/#Model_16B   , you see that the description of this model says it has a squelch control which was turned on and off by a switch on the side panel, and controlled by a potentiometer on the back of the set.
#5

Yes, Philco calls it the QAVC switch #54 on the diagram. I think your tuning shaft is missing a threaded hole in it's center.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#6

Some 16B sets used a tuning knob with a set screw on the side. These will not have the drilled and tapped tuning shaft.

--
Ron Ramirez
Ferdinand IN
#7

Have No clue to what you guys mean ...

tuning knob with a set screw on the side. These will not have the drilled and tapped tuning shaft.

Skip
#8

I don't know that I've seen a rosette knob w/ a set screw in the side. I have in the front and hex w/a screw in the side.

Skip,
On the early 16B'B the two speed tuning mechanism requires that you pull the tuning knob out or push it in to change speeds. Most of the knobs have a spring steel clip that holds them onto the shaft. On this sets it needs screw to hold the knob in place. When you use a non set screw knob it will pull off. If you look closely at the 2nd gallery pic you'll see a hole in the tuning knob. That one is missing the screw. The later model sets w/ hex knobs had a small set screw in the knob.

YMMV

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#9

Questions about Chuck have been moved into their own thread.




Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
My last cabinet for this year
They are a nice looking radio, Stromberg. I have a small tabletop octagon-dial one. It sounds surprisingly nice. And t...morzh — 09:40 PM
Philco 41-608 changer coupler
Different years but the same idea.morzh — 09:38 PM
My last cabinet for this year
That’s a beauty! :thumbup:klondike98 — 09:24 PM
Philco 41-608 changer coupler
Hi Morzh, I've searched using Mondial as the user name with various keywords such as 'coupler', 'motor', 'idler', 'p...alangard — 08:31 PM
Philco 16B Parts
I think the chassis is painted.morzh — 08:13 PM
Philco 38-2 Automatic Tuning
Honestrly, the original is quite acceptable and, it seems to me, can be cleaned.morzh — 08:11 PM
Philco 41-608 changer coupler
Mondial left a thread about remanufacturing thois type coupler.morzh — 08:09 PM
IF can wire size and Rubber mounts?
Are you talking about rewinding or rewiring? For rewiring, meaning runnin wires to the coil from other components, the ...morzh — 08:08 PM
12' Philco
I wonder who would be able to "no stoop" with this one.morzh — 08:05 PM
IF can wire size and Rubber mounts?
Hello PHORUM members, I am still working on restoration of my PHILCO 37-640.  I want to start with rewiring the IF ca...georgetownjohn — 06:32 PM

[-]
Who's Online
There are currently 3516 online users. [Complete List]
» 1 Member(s) | 3515 Guest(s)
Avatar

>