Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Dry Cleaning grill cloth
#1

Hi  All   Just wondering, since the grill cloth on my 38-116 only has a couple small holes but is very dirty, has anyone taken their grill cloth to a dry cleaners while still attached to the sound board?  I would think they could be more careful when it is still stretched out than when it is loose.  Any experience or opinions are welcome.  
Thanks
Dick
#2

I have tried soaking old cloth in a mixture of Woolite and water, with mixed results. Most turned out ok but some fell apart in the Woolite bath.

I doubt that the dry cleaners could do anything with the cloth while still attached to the board, but I could be wrong...

--
Ron Ramirez
Ferdinand IN
#3

Thanks for the response Ron.  I agree I kind of doubt they can do anything also but I might just visit a local dry cleaner and get their opinion.  Can't hurt to ask.  
As far as washing myself, I have yet to have one stand up to the task even when trying to be very gentile.  The cloth just seems to evaporate.
Thanks again
Dick
#4

i used to repair dry cleaning machines. they are nothing more than a front load washer that uses a chemical rather than soap and water. so thats a non starter. older perchlorethylene machines might even melt what you have if it is synthetic. on my 48-482 i removed the grill cloth and let it soak in strong dish soap/water  solution. the method is to squeeze not rub it against itself. as it was sun faded.so after i rinsed and dried it i flipped it around  and reglued it back on. considering i couldnt find anything really close, gold with a reddish tint  im reasonably happy although like most times at bat it would be better with practice. beware of irish pennants during the re-glue if you re use it .
#5

I agree that trying to wash most grill cloth is a frustrating exercise and I have not been successful trying it.  I did get lucky when restoring my 48-482 cloth with a find in a Joann's Fabric store.  It was blind luck I think and probably not something that will be repeated but the replacement was remarkably similar to the original.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM
two videos to watch VHS and history of TV
Hello Every, Here are a couple videos right up my alley VHS and the history of Television . history of VCR VHS Hi...radiorich — 02:13 PM
Made mistake & did not label connection
You haven't given us the model number of the set so I looked up the 6A8 pin assignment. Pin 8 is the cathode and pin 7 i...RodB — 01:19 PM
Made mistake & did not label connection
Happy Thanksgiving all! I have made a real bonehead mistake this time. Hope someone can help.  I am trying to determi...georgetownjohn — 12:51 PM
New Philco Repair Bench
Apparently there is a new Philco Repair Bench found at https://philcoradio.com/repairbench/ When I try to go to order a ...dconant — 12:00 PM
Philco 60 Squealing
Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM

[-]
Who's Online
There are currently 2536 online users. [Complete List]
» 1 Member(s) | 2535 Guest(s)
Avatar

>