Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 37-116 label/graphics question
#1

Hi all,

Been following this forum for awhile, but this is my first post. I'm putting graphics on a 37-116. Radio Daze includes a graphic for the band selector lever. In every picture I look at, for both restored and seemingly original 37-116s, graphics are over the knobs but there is not one for the band selector lever. Even in the original advertising, I can't seem to make one out.


I asked on another forum and it seems that the 37-116 did not include a graphic/label over the band selector lever, but I thought I would get opinions here as well.

Thanks for any insight.

- Steve
#2

Hello Steve, and welcome to the Phorum! I haven't seen more than a couple 37-116's. I'm sure one of our members will have an answer for you. Take care and BE HEALTHY! Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#3

Thanks Gary!

- Steve
#4

Phico did not use a decal for the band switch function on the 37-116.

--
Ron Ramirez
Ferdinand IN
#5

Thank you Ron!
#6

I knew you would get a quick answer on this! Post a photo or two of your project when you have a chance, and don't be a stranger. Take care and BE HEALTHY! Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#7

There's not much need to label the band switch. Mine isn't (original finish). The selected band is illuminated on the dial.

Can't think of anything witty.
Greg O.
Whitehall, PA




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 3034 online users. [Complete List]
» 2 Member(s) | 3032 Guest(s)
AvatarAvatar

>