Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco cabinet feet - component parts
#1

Hello Gang,

I just wanted to share a few pics I took during my 37-60 cabinet refurbishing. 

I took apart one of the feet and saw that it looks like it was originally built in three parts: 

Part 1: A blackened brass snap fastener seat part, size 1/2” marked “Mattatuck Waterbury”
Part 2: A common rug tack, or flat head tack
Part 3: A brown felt disc, roughly 7/16” in diameter 

Now, it just so happens that I know Mattatuck brass fasteners were one of many US Government contract suppliers of material for the military during WW1 (and afterwards). 

I wonder if Philco bought up these surplus fastener parts 10-20 years later for use as cabinet feet?

In any case, it struck me as an interesting tid bit to share on Veterans Day. 

Thanks to all of you who served. 

Michael (mbhdesign)


Attached Files Image(s)
               

mbhdesign
Michael Hennessey
#2

Interesting, thanks for that information. If you are looking for some replacements I know Steve Davis was thinking about making some available. You can check with him.
#3

Hi Bob,

Yes, Steve Davis’ brass lathe turned feet are very impressive. It’s interesting too that the original foot shown on his website seems more straight sided, cylindrical, and substantial than the types I have on my 37-60 and 38-12.

I’m going to see if I can replicate these feet using similar parts to the ones I disassembled.

mbhdesign
Michael Hennessey
#4

Hello mbhdesign ,
Very intresting and that would be great to see your results ! Bob
I read that post of Steve's that they look good .

Sincerely Richard




Users browsing this thread:
[-]
Recent Posts
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM
Philco 91 Speaker Replacement
Yes, I often have to substitute, then keep an eye out for an original. In the meantime, the radio is working and being e...RodB — 08:02 AM

[-]
Who's Online
There are currently 3193 online users. [Complete List]
» 2 Member(s) | 3191 Guest(s)
AvatarAvatar

>