Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Cleaning Gang Switches etc.
#1

In the old days they had a foaming blue cleaner that was great for cleaning switches tuners and tarnished connections... Is there a good product now for that or what are you using? Maybe something I could get in a hardware store?


Attached Files Image(s)
   
#2

Blue Showers...

There is risk of phenolic penetration and leakage. Blue showers was intended to polish the contacts as it had grit in the mix for TV tuners.

In a radio, if the circuit is not known, there could be B+ switched, a cleaning product could cause leakage to the shaft and burn out the wafer.

I use 91% alcohol and an acid brush, back up the switch with a clean cotton rag to soak up excess and contaminates.. Massage the brushing all the way around each side of the wafer, then turn the switch in the opposite direction, clean again. Blow dry thoroughly as the alcohol will chill and cause condensation, warming gently the sections will thoroughly dry. Alcohol will remove all the old rosin residue and any other contaminate. Look at the actuation of the contacts each contact should rise/fall as the connection is made/broken, this is a self-wiping action. Black silver oxide still conducts.

De-Oxit applied with a stylus to only the contacts will help, never saturate the phenolic wafer as this will cause leakage.

GL

Chas

Pliny the younger
“nihil novum nihil varium nihil quod non semel spectasse sufficiat”
#3

We used to use carbon tetracloride. It was GREAT for cleaning switches and also potentiometers. It was quite inert so it didn't destroy the wafers, or the resistance element of the pots. It evaporated VERY fast and was non-conductive. I had a bottle for years which I used until it finally ran out.

(political content removed by admin)
#4

Good to know, I'll get some high strength alcohol and give it a go. thanks!
#5

When I was a kid, the local jobber sold 2 products, the afore mentioned "Blue Shower" that you can bathe the control in and "Blue Stuff," an abrasive (I believe) cleaner and lube that you had to judiciously and carefully to contacts to prevent detuning.

In the BioMed Shop at the hospital I worked at in my senior year at high school and freshman year at college, we used several Miller-Stephenson products such as "Contact Re-Nu". The product had a hose and brush wand that attached to the can, was very handy. M-S also made a PC Board wash and a flux remover

"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
Best Regards, 

MrFixr55




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 4002 online users. [Complete List]
» 1 Member(s) | 4001 Guest(s)
Avatar

>