1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 51-930 cabinet restoration
radiorich
Phorum Expert
*****
Posts: 1,610
Threads: 102
Joined: May 2008
City: Omak State, Province, Country: WA
#1

11-20-2022, 06:06 PM
Hello guys,
I am restoring my Philco 51-930 and the chassis is complete now it's time for the cabinet .
you can see how grimmy and nasty this cabinet is so first thing   is removing the Dial cover and bezal there some screws and a couple clips that go over some posts so what is the easiest why to deal with those two clips with out damaging them or the dial .

Sincerely Richard
P.S. what would you suggest to clean the cabinet I have go jo  hand cleaner !


Attached Files Image(s)
       
Find
radiorich
Phorum Expert
*****
Posts: 1,610
Threads: 102
Joined: May 2008
City: Omak State, Province, Country: WA
#2

12-01-2022, 10:03 PM
Hello Guys,
I got the clips removed and took the dial and brass trim out plus the cardboard speaker baffle .
Here is a photo of a good start on polishing my Philco ! 
Sincerely Richard


Attached Files Image(s)
   
(This post was last modified: 12-01-2022, 10:05 PM by radiorich.)
Find
radiorich
Phorum Expert
*****
Posts: 1,610
Threads: 102
Joined: May 2008
City: Omak State, Province, Country: WA
#3

02-05-2023, 01:56 AM
Hello Guys,
Here is my Philco I finished it today !

Sincerely Richard


Attached Files Image(s)
   
(This post was last modified: 02-05-2023, 02:01 AM by radiorich.)
Find
Paul Philco322
Super Moderator
******
Posts: 4,384
Threads: 412
Joined: Jun 2011
City: Boston State, Province, Country: Massachusetts
#4

02-05-2023, 08:48 AM
Looks like it just came home from the store!.

Paul
Tubetalk1
Website Find
radiorich
Phorum Expert
*****
Posts: 1,610
Threads: 102
Joined: May 2008
City: Omak State, Province, Country: WA
#5

02-05-2023, 05:03 PM
hello Paul,
Yes, the set turned out really nice and sounds great thank you to Terry for his advice to add a resistor in the audio output stage making a RC circuit .
Well I also changed the audio output tube from a 35 to a 50 .

Sincerely Richard
Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Rusty Tuning Condenser
Thanks guys. I think I'll give the Naval Jelly a try since I can better control where it goes.dconant — 09:23 AM
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM

[-]
Who's Online
There are currently 3929 online users. [Complete List]
» 1 Member(s) | 3928 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration