Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

General Television - unknown model
#16

Lookin' good so far!! Wonder what would happen if you took to washing the grill cloth, it looks like that there is enough nicotine and tar on it to be positively carcinogenic!

"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
Best Regards, 

MrFixr55
#17

I may try to give it a wash but to be honest I have had little success at washing these old grill cloths. In this case it’s almost invisible behind the wood grill and I do have some suitable replacement cloth so a wash might be worth a try.
#18

The washing worked out pretty well. Here's a before & after with the wash water in the middle. I used baby shampoo with warm water and very gentle movement of the cloth in the water for about 10 minutes. After washing I rinsed multiple times and then blotted it dry on paper towels and let it air dry. It could probably use another 10 min wash but I'm going to leave it where it is.

[Image: https://www.dropbox.com/s/eydr16icu2cpns....jpg?raw=1]
#19

That's an interesting pattern, considering that it is rather hidden behind a wooden grille. Wonder if they had i style for most of their radios with either an open face or a grilled face.

This is shaping up to being a real nice restoration!

"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
Best Regards, 

MrFixr55
#20

The JB Weld filling the thread grooves for the knob set screw worked great. I retapped the threads without redrilling it. I also put in a slightly longer set screw so it would have an extra thread or two for grip. Set screw tightened down nicely. Thanks Gary, David and MrFixr.




Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Gilfillan Brothers Car Radio?
There is a Mission Bell model 19/19A that could be what you’re looking for, Riders vol 4. It has the tube line-up of: 0Z...Joe Rossi — 05:01 PM
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
Hickok AC51 tube tester
How does the  5W4 and 83 tube filaments get fed?martinj — 12:25 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM

[-]
Who's Online
There are currently 2601 online users. [Complete List]
» 2 Member(s) | 2599 Guest(s)
AvatarAvatar

>