1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco Model 90 volume pot value
WyTex
Senior Member
****
Posts: 289
Threads: 42
Joined: Jan 2014
City: Jeffersonville State, Province, Country: PA
#1

03-08-2023, 08:38 PM
Hey fellas - 

Continuing a battle with a Model 90 w/single 47 tube version.  There's audible audio when turned all the way down plus some strange crackling after 10-15 minutes of use.   Volume pot part #5366 does not list a value and haven't been able to locate it.  I'm suspecting this one might be bad and have a spare.  The current pot measures 676k while the spare measures 215k.  

Thanks,
Paul
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
#2

03-08-2023, 11:39 PM
1/2 meg.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
radiorich
Phorum Expert
*****
Posts: 1,472
Threads: 89
Joined: May 2008
City: Omak State, Province, Country: WA
#3

03-09-2023, 09:04 AM
Hello Paul,
One thing I would check is disconnect that volume control and hook an meter on it to
check how smooth the volume resistance changes and if you have one an old analog meter like my Simpson 260 works well for this !

Sincerely Richard
Find
WyTex
Senior Member
****
Posts: 289
Threads: 42
Joined: Jan 2014
City: Jeffersonville State, Province, Country: PA
#4

03-09-2023, 12:52 PM
Thank you Terry and Richard.  I also happen to have a Simpson 260 and will test.

Paul
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently 3967 online users. [Complete List]
» 1 Member(s) | 3966 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration