Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Alkaline or Heavy Duty batteries in our old portable radios?
#1

I've been on a vintage solid state kick again and have been tinkering with my old Zeniths from that era. I dug out my rebuilt Royal 2000 and realized the old sets of alkaline batteries I have been using are no longer trustworthy, so I bought two six packs of heavy duty Rayovac D cells at Big Lots for a little over $10 with the tax included. My realization is that this radio and others I have were made before alkaline batteries were even a thing and will work just as well with the cheaper carbon type. I have four batteries left over and another pack will allow me to get my Royal 3000 up and going as well. Might be interesting to see how long these batteries will last in the rebuilt Zeniths compared to the alkaline D cells. $10.65 for 12 batteries is a lot cheaper than even the store brand alkaline batteries in my area and there might be stores with the Heavy Duty even cheaper yet. Shopping around right now in my area is almost dangerous with constantly angry and careless drivers. So, now to make my Royal 2000 my Christmas radio!

No matter where you go, there you are.
#2

Doesn’t really matter what type even quality. What matters is forgetting that batteries have been left inside and the potential for leakage.

On older radios, often, there is a bypass capacitor across the battery at all times. If this capacitor is electrically leaking the battery will be slowly discharged inviting chemical leakages. This can be avoided by checking for this “phantom” current flow and correcting it.

Chas

Pliny the younger
“nihil novum nihil varium nihil quod non semel spectasse sufficiat”
#3

Never leave a battery in a radio! When you turn it off take them out. I am not happy with the way any batteries are being made at this time, brand name or store name most are JUNK! Sorry about the rant have purchased batteries and had them start leaking in a few weeks and still in the new packing.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM

[-]
Who's Online
There are currently 7793 online users. [Complete List]
» 1 Member(s) | 7792 Guest(s)
Avatar

>