1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Removing big paint lumps
bridkarl
Member
***
Posts: 182
Threads: 39
Joined: May 2023
City: Pocatello State, Province, Country: idaho
#1

02-25-2024, 01:39 AM
Someone has dropped a huge lump of paint on this metal case. Any thoughts on how to soften this up for removal? Usually I start with WD-40 or goo-be-gone but this looks like I’d need to file it off. Not a Philco, but this seemed the best place to put this question.


Attached Files Image(s)
   
Find
Arran
Phorum Expert
*****
Posts: 4,705
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#2

02-25-2024, 03:14 PM
It looks more like tar splashed on it, or maybe wax? It may melt off with a bit of heat but mineral spirits should work as well.
Find
GarySP
Super Moderator
******
Posts: 1,975
Threads: 147
Joined: Jan 2013
City: Westland, MI
#3

02-25-2024, 08:19 PM
I'd try heating it with a heat gun slowly to soften the mass, then carefully scrape it with a putty knife. Are you repainting the entire cabinet? Take care and BE HEALTHY! Gary
"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
Find
slford310
Member
***
Posts: 109
Threads: 25
Joined: Jul 2022
City: Monticello State, Province, Country: Illinois
#4

03-02-2024, 08:31 PM
Kind of reminds me of a big blob of solder that splashed on it.  
Philco's 
86 Low Boy     71B      42-321T
90 High Boy    52B      46-1203
95 High Boy    118B     48-214     
112X Console     60B       48-206
118X Console     84B       49-506
41-608P Console   610B   76 High Boy
41-265 Console   37-89B   370LZ
52GC                38-35B
20 Baby Grand   38-10T
70 Baby Grand   41-221CI

Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration