Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Unusual High Boy console
#16

Please do take additional detailed photos, and keep us informed on progress. It would be nice to know the tube line-up. Joe

Joe

Matthew 16:26 "For what does it profit a man if he gain the whole world, yet lose his own soul?"
#17

The rolled up paper above the metal ID plate may have some info. Looking forward to more pictures. David
#18

If you'd like to bone up on the 16's here's a good start. https://www.tuberadioland.com/philco16L_main.html

The tabletop sets (B's) and the consoles use the same chassis except for the power transformer, rectifier tube, and speaker. Console sets are larger. Something else that Philco employed in their 1933/34 sets was inter station noise suppression (aka qavc). That's what the switch on the right side of the cabinet turns off and on. There's a control shaft on the back of the chassis that sets the level.

I have one on the bench (the chassis done) in limbo as I need to finish up the cabinet. And a couple of others too. There are a plethora of folks here that are well versed in the workings of Philco sets. Drop by if you have any questions.

Here's a thread I started several yrs ago. https://philcoradio.com/phorum/showthread.php?tid=20055
Cabinet https://philcoradio.com/phorum/showthread.php?tid=19986

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#19

Terry

I have never said it was 14 or 18; I merely pointed to the escutcheon as the one used in those, and then answered the escutcheon question.
Now that I see the chassis, I see it is a Philco, that is without doubt.

I suspect it could be 16 / 18 modification for a non-US market, due to the combination of the holes in the chassis, the speaker plug and the capacitive filter can.
In fact the label says 18T.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit.  That would rem...alangard — 09:30 PM
HiFi (Chifi) tube amp build - but my own design.
Tim Well...a chassis is metal. Magnetic or not, it does not matter. A transformer has some hum to it. It is natural....morzh — 08:40 PM
Shadow Meter Bulb
Ross I am not sure what current limiting effect the incandescent provides. They are two different parts of the sch...morzh — 08:31 PM
12' Philco
Bob Thanks for that photo. I have been looking for it, and I cannot find anythinmg on the web. I forgot it was here...morzh — 08:29 PM
Shadow Meter Bulb
I think after all has been said, I will use the same bulb that is specified for the dial pilot light which is a #55. I ...georgetownjohn — 07:31 PM
12' Philco
There was also this Philco! klondike98 — 07:25 PM
HiFi (Chifi) tube amp build - but my own design.
I expected a challenge and this is just part of it. But, it's also supposed to be fun, entertaining, informative and enj...TV MAN — 07:12 PM
Shadow Meter Bulb
Butting in here with a question. Since the shadow meter is connected directly to the 1st and 2nd I.F.'s wouldn't the met...RossH — 06:43 PM
HiFi (Chifi) tube amp build - but my own design.
Mike, Tim; you are about to enter the twilight zone. Doo doo doo doo, doo doo doo doo This is something alright. I'm go...RodB — 06:26 PM
HiFi (Chifi) tube amp build - but my own design.
:lol: We need to start a singing radio group! I play the guitar, so maybe get a few vocals? Anyways, Mike, I did try mou...TV MAN — 05:56 PM

[-]
Who's Online
There are currently 6478 online users. [Complete List]
» 3 Member(s) | 6475 Guest(s)
AvatarAvatarAvatar

>